background image

170

225

233

241

393

401

385

16

72

80

64

8

1

Fit bottom guide unit

Screw the bottom guide unit, 173 mm from the 
front edge of the cabinet, as per the drawing, to 
the middle of the bottom shelf

Fastening material  

(not included):

Pan head screws 4,0 x 16 
or Euro screws 6,3 x 13

4

Fit sliding frame

Pull the bottom guide out of the cabinet
to the stop and fit the sliding frame with 
the holes over the adjusting screws 
provided. Push down the sliding frame 
until it engages in the guide.
Now pull the top ball bearing guide also 
out to the stop and pull up the top sliding 
section of the frame until it is underneath 
the top guide such that the two fastening 
pins on the top guide protrude through 
the cover plate. Secure these pins with 
the plastic clips. Now push in the entire 
sliding frame and pull it back out again, 
then finally tighten the clamping screws 
on the sliding frame.

2

Fit top guide

Screw the top guide, 170 mm from the front edge 
of the cabinet, to the middle of the top

Fastening material  

(not included):

Pan head screws 4,0 x 16 
or Euro screws 6,3 x 13

3

Fit coupling arms top / bottom

When fitting the coupling arms it is to
be ensured that the straight coupling
arm is fitted at the top, and the bent 
coupling arm is fitted at the bottom.
The brackets for the coupling arms 
are (with 110° hinges) to be fastened
such that from the edge of the 
cabinet (hinge-side) to the 1st screw 
hole on the bracket there is a 
distance of "94 mm + door overlap".

Fastening material  

(not included):

Pan head screws 4,0 x 16 
or Euro screws 6,3 x 13

173

213

181

453

485

128

Pan head screws 4.0 x 16 
or Euro screws 6.3 x 13

Bottom shelf

Guide unit

Cabinet front edge

Cabinet front edge

Cabinet front edge

Cabinet front edge

Pan head screws 4.0 x 16 

or Euro screws 6.3 x 13

Top

Ball bearing guide

Top

94 mm +

door overlap

32

Door

20 mm +

door overlap

20 mm +

door overlap

Pan head screws 4.0 x 16 

or Euro screws 6.3 x 13

Bracket

Coupling arm

Bottom of door

Top of door

Coupling arm

Bracket

Pan head screws 4.0 x 16 

or Euro screws 6.3 x 13

Bottom shelf

Summary of Contents for Dusa Series

Page 1: ...et width depth height 365 110 60 Installation dimensions Heights DUSA 1 650 mm 950 mm 2 baskets DUSA 2 950 mm 1200 mm 3 baskets DUSA 3 1200 mm 1450 mm 4 baskets DUSA 4 1450 mm 1700 mm 4 baskets DUSA 5 1700 mm 1950 mm 5 baskets DUSA 6 1900 mm 2150 mm 5 baskets DUSA 7 2150 mm 2350 mm 7 baskets Finish Fitting RAL 9006 silver clear varnish Baskets chrome RAL 9006 silver clear varnish Damping available...

Page 2: ... 170 mm from the front edge of the cabinet to the middle of the top Fastening material not included Pan head screws 4 0 x 16 or Euro screws 6 3 x 13 3 Fit coupling arms top bottom When fitting the coupling arms it is to be ensured that the straight coupling arm is fitted at the top and the bent coupling arm is fitted at the bottom The brackets for the coupling arms are with 110 hinges to be fasten...

Page 3: ...e same as dimension A as per table A The position of the top plastic bracket is dependent on the installation height The distance B is to be found in table A If there are fouls with existing front hinges then the dimension A will need to be adjusted as appropriate Caution this situation must also be taken into account in point 8 Fit front frame Now place the rails in the plastic brackets and conne...

Page 4: ...ame guides onto the rollers on the rails Screw the plastic brackets to the front Fastening material Pan head screws 4 0 x 20 not included Fastening screws 4 0 x 8 9 Fit the baskets The plastic clip the clips are symmetrical is clipped into the holes on the sliding frame The baskets are now hung on the sliding frame with the top wire on the side rail in the plastic clip The height of the baskets ca...

Reviews: