background image

6

charGinG WarninGS

 

»

Read all safety precautions and  

literature prior to use of this product.

 

»

Never leave the battery and charger 

unattended during use.

 

»

Never allow children under 14 years  

of age to charge batteries.

 

»

Never attempt to charge dead  

or damaged batteries.

 

»

Never charge a battery if the cable  

has been pinched or shorted.

 

»

Never allow the batteries or charger  

to come into contact with moisture  

at any time.

 

»

Never charge batteries in extremely 

hot or cold places (recommended 

between 50–80°F (10–26°C)) or  

place in direct sunlight.

 

»

Always use only Ni-MH rechargeable 

batteries. This charger cannot charge 

batteries such as “heavy duty”, “alka-

line”, “mercury” or “lithium” batteries.

 

»

Always connect to the charger  

correctly.

 

»

Always disconnect the battery and 

charger after charging and let them 

cool between charges.

 

»

Always inspect the battery before 

charging.

 

»

Always terminate all processes and 

contact Horizon Hobby if the product 

malfunctions.

 

»

Always make sure you know the speci-

fications of the battery to be charged 

or discharged to ensure it meets the 

requirements of this charger.

 

»

Always constantly monitor the tem-

perature of the battery while charging.

 

»

Always end the charging process if the 

charger or battery becomes hot to the 

touch or starts to change form during 

the charge process.

1

  Connect the AC power cord to  

the power slot on the charger, then 

connect the other end of the power 

cord to an AC power source.

2

  The Power LED and Charging LED  

will turn green when the charger is 

connected to the AC power source.

3

  Connect the battery connector  

to the charger connector.

4

  Press the Start/Stop button to 

charge the battery. The Charging  

LED turns red.

5

  When the battery is fully charged,  

the Charging LED will turn green.

6

  Press the Start/Stop button to stop 

charging. Disconnect the battery  

pack connector from the charger 

connector.

7

  Disconnect the AC power cord  

from the AC power source.

a

  Power LED

B

  Start/Stop Button

c

  Charging LED

d

  AC Power Slot

e

  Charger to Battery 

Connector

Refer to the charging warnings. It is  

recommended you charge the battery 

while you inspect the vehicle. The  

battery will be required to confirm  

proper operation in future steps.

warnInG:

 Failure to exercise 

caution while using this product and 

comply with the following warnings 

could result in product malfunction, 

electrical issues, excessive heat,  

FIRE, and ultimately injury and 

property damage.

CauTIon:

 If at any time  

during the charging process the 

battery becomes hot to the touch, 

disconnect the battery immediately 

and discontinue the charging process.

Charge only batteries that are cool  

to the touch and are not damaged. 

Inspect the battery to make sure it  

is not damaged, e.g., swollen, bent,  

broken or punctured.

The VehICle baTTery  

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

 

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 

B

c

d

a

e

Summary of Contents for Vaterra Kemora 4WD Rallycross 1/14th RTR



















Reviews: