background image

14

• 

Power OFF the ESC and then power ON the ESC to return to normal operation.

oPeration

led StatuS

waiting

 

for

 

throttle

 

position

position

 

set

neutral

Flashing Green

Solid Green (1 second)

forward

Flashing Red

Solid Red (1 second)

full Brake/reverse

Solid Red 

/

 Flashing Green

Solid Green (1 second) followed by Red and Green flashing 3x

c  change eSc running Mode: forward/

reverse with Smart Brake forward 

only with Brake or crawler Mode

• 

The green LED will indicate the  

currently selected ESC running  

mode for 4 seconds:

 

-

Green

 Forward/Reverse 

 

LED Solid 

with Smart Brake

 

-

Green LED 

Forward Only

 

Flashing

 

 with Brake

 

-

Red + Green

 

LED Solid 

Crawler Mode*

• 

Move the throttle trigger to full throttle 

within the 4 seconds to select the next 

ESC mode. A beep will sound and the 

green LED will indicate the new ESC 

running mode.

• 

To select the next mode, repeat the 

step above within 4 seconds of the 

beep.

• 

Both red and green LEDs will flash  

3 times with 3 beeps.

• 

Power OFF the ESC and then power on 

the ESC to return to normal operation

• 

At any time that the ESC is powered 

and the transmitter is at neutral, the 

green LED will indicate the current  

running mode:

 

-

Green

 Forward/Reverse 

 

LED Solid  

with Smart Brake

 

-

Green LED

 

Forward Only  

Flashing  

with Brake

 

-

Red + Green

 

LED Solid 

Crawler Mode*

noTiCe: 

Crawler mode is for use on 

rocky surfaces only. Do not use this 

mode with your vehicle on any other 

surface, especially pavement. Doing  

so may damage the vehicle.

SMart Brake

When the throttle is changed from  

Forward to Reverse or Reverse to  

Forward, the ESC will brake instead  

of reversing the motor immediately.  

The ESC will remain in brake mode 

unless the throttle is returned to the 

neutral/stop position for a short time.

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

Summary of Contents for Nissan Silvia S15 V100-C




















Reviews: