background image

EN

Your Spektrum Transmitter comes 

prebound to the vehicle.
If you encounter problems, obey 

binding instructions and refer to the 

transmitter troubleshooting guide for 

other instructions. If needed, contact 

the appropriate Horizon Product  

Support office.

BindinG Procedure

1

  Make sure the transmitter and vehicle are both powered OFF.

2

  Install a bind plug in the receiver battery/bind port. You  

do not need to remove any of the other plugs to re-bind.

3

  With the bind plug installed, power ON the vehicle.  

The receiver LED will flash green.

4

  Move the steering wheel and throttle trigger to the failsafe 

positions and continue to hold those postions until the  

binding process is complete.

5

  Press the bind button on the transmitter while powering on 

the transmitter. The green LED on the transmitter will flash 

after 4 seconds when the transmitter is in bind mode.

6

  Release the bind button after the red LED on the  

transmitter flashes. Continue holding the failsafe positions 

until the receiver LED is solid. The green LED on the receiver 

will glow solid when the transmitter and receiver are bound.

7

  Disconnect the battery from the ESC. Remove the bind plug 

from the receiver. The receiver will keep the binding to the  

transmitter until another binding is done.

TransmiTTer anD reCeiver binDinG 

 / / / / / / / / / / / / / / /

 

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

ConTrol TesT 

 / / / / / / / / / / / / / / /

 

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

Perform a control test with the vehicle 

wheels off the ground. If the wheels 

rotate after the vehicle is powered  

ON, adjust the “TH. Trim” knob until 

they stop. To make the wheels move 

forward, pull the trigger. To reverse 

them, wait for the wheels to stop, 

then push the trigger. When moving 

forward, the wheels should maintain 

a straight line without any steering 

wheel input. If not, adjust the “ST. 

Trim” knob so the wheels maintain  

a straight line without having to  

turn the steering wheel.

Brake/reVerSe

forWard

Summary of Contents for Nissan Silvia S15 V100-C




















Reviews: