manualshive.com logo in svg

VAT 650 GS Series, Installation, Operating, & Maintenance Instructions

Share
Download
VAT 650 GS Series Installation, Operating, & Maintenance Instructions Download Page 64

 

Installation, Operating & Maintenance Instructions 

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

 

 

 

 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 

Tel ++41 81 771 61 61  Fax ++41 81 771 48 30  Email 

[email protected]

  

www.vatvalve.com 

271149EA

 

2007-06-12 

64/77 

 

D e s c r i p t i o n 

Required tool 

 

 

Note: For Replacement of actuator 
or actuator shaft seals, proceed with 
step 19 otherwise go to step 17. 

 

17.  Reassembly the valve in reverse 

order, step 9…3. 

18.  Close the valve bonnet, see steps 

40…42.

 

 

 

 

 

19.  Release the valve from safety mode. 

Refer to «Safety mode» for details 

 

20.  Move the valve to position 50% (half 

opened) This is necessary, in order 
to dismount the actuator. See step 
24. 

 

21.  Disable PFO option feature via 

'Power Fail Status' in menu 'System' 
of CV or CPA software, and turn off 
the power 

 

 

 

 

 

 

 

•

 CV software  

 
 
 
 
 
 
 
 

•

 CPA software 

 
 
 
 
or 
 
 

•

 Service Box 2 

 

 

22.  Disconnect 24VDC power. Wait for 

60s, then disconnect cables and 
compressed air from valve actuator. 

 

23.  Unfasten all 4 controller screws and 

lift controller carefully from actuator. 

 

 

 

Allen Wrench 

4 mm 

 

 

Summary of Contents for 650 GS Series














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands