background image

 

 

Introduction: 

Thank you

 for purchasing your printing equipment form Vastex International Inc.  

Vastex has been designing and building printing equipment since 1960. We have the knowledge and 
experience, and are supplying the printing industry with quality equipment at an affordable price. 
You can be confident your purchase will give you years of trouble free service. 

Vastex Exposing Units 

(LED Exposure Systems) 

E200 (E2-2128) 

Specifications & Part Numbers 

Overall Size  

(lid closed) 

Depth x Width x Height

 

Screen Capacity 

21" x 28" 

Weight 

Vacuum Pump 

1/16 Hp Diaphragm Pump            

(120V P/N: 04-02-040)                 
(240V P/N: 04-02-041)

 

151 lbs.  

(68.5kg)

 

Power Requirements 

120v: 60Hz @ 3.5 Amps 
240v: 50/60Hz @ 2 Amps 

LED Power Supply 

P/N: 04-08-057

 

Warranty 

Floor Model/Tabletop 

Table Top, optional stand available  

Glass Reorder Numbers 

P/N: 04-08-060 

Vacuum Blanket 

P/N: EUB-2128 

Lid Seal 

P/N: 04-08-039 

3 Years; Manufacturer Defects 

32.75” x 37.75” x 14” 

(83 x  88 x 36 cm) 

Vacuum & exposure Timer 

Analog 

P/N 04-01-085

 

LED Light Bar 

LED Light Bars       

P/N: 04-08-056

 

2

Summary of Contents for E2-2128













Reviews: