background image

V-SPB5.2

4

·

After cutting and drilling all holes, inspect the mounting areas for any metal burrs or rough edges. File any area that may interfere with the mounting of
the speaker.

·

Clean any metal shavings from the mounting area and check for areas in which water may enter the speaker cavity.  Treat the area for water protection
when necessary.

Securing the speakers

·

Position the speaker into the mounting hole and re-confirm the correct mounting location and hole placement.

·

Screw clips are provided to ensure a snug fit. These should be placed over the metal surface and line up the hole you have previously drilled with the
screw clip. Place the speaker into the hole, align the holes and proceed to insert the screws. Be sure to tighten the screws evenly so that it will not warp
the speaker frame.

·

Turn your system back on and confirm the speakers operation first at a low volume and then you may increase the volume as you desire.

·

After installation acoustic system and having tested it the speaker grill will have to be inserted. Turn on you system and follow these steps carefully:

-  locate the speaker grill;
-  now carefully inspect the place where the speaker grill will be mounted   there should be no blowholes;
-  fix the speaker grill by screws.

Summary of Contents for V-SPB402















Reviews: