background image

V-SPB5.2

3

·

Make sure the wire of the negative pole terminal is disconnected from accumulator while connecting the speaker terminals. Turn on the various
components and slowly advance the volume. Remember to check and re-check all connections to insure proper installation and use.

·

Do not continuously use the speaker system beyond the nominal power handling capacity.

·

Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to protect them from damage caused by the
magnets in the speakers.

·

If you cannot find the appropriate mounting location, consult your car dealer or your nearest dealer before mounting.

CAUTION

: Take extreme caution when working near the gas tank, gas lines, brake or hydraulic lines and electrical wiring.

Mounting the speakers

Installation kits are available from your dealer or local stereo shop to help make your installation easy. These kits also give your installation a clean, custom
appearance. Questions about installations methods please consult a professional auto sound dealer/installer for assistance.

·

Choose the place of installation for acoustic system. For most acoustic system stipulated regular places in the automobile approach. In this case you need
to know only assembly depth. Before installation acoustic system check up their assembly depth.

·

At a choice of a non-standard arrangement of speakers at which it is necessary to cut them in panels of the automobile, use a mould (not included). For
achievement of ideal arrangement of acoustic system keep up geometry of a mould, as it is very important for correct installation of your system

=137 mm, Ø =5 mm).

·

If it will be necessary to cut steel, reinstall the cosmetic panel in place and use the hole you have previously cut as a template. This will help to insure
proper cutting and a good fit. Now, mark the locations for the speakers mounting screws, remove the panel and drill the screw holes. When finished you
may replace the panel.

Summary of Contents for V-SPB402















Reviews: