background image

 

POWX1190 

EN

 

Copyright © 2020 VARO NV 

S t r a n a

 | 

7

 

www.varo.com 

8.3 

Handle attachment (Fig. 2) 

For reasons of safety, only use the hammer drill with handle attachment. 
You will be able to obtain a safe body position when working by rotating the handle attachment.  

8.3.1 

Side handle 

The auxiliary handle can be attached in two different mounting holes: left and right. 
remove the auxiliary handle subassembly in the opposite way. 

8.3.2 

D-shaped handle 

 

To loosen: turn fixation knob (3) to the left.  

 

Now the handle can be turned in the desired position. 

 

Tighten the fixation knob (3) again, by turning to the right. 

8.4 

Use 

 

Set de mode selector (6) to hammer mode 

 

After placing the tip of the tool on concrete surface, switch ON 

 

By utilizing the weight of the machine and by firmly holding the hammer drill with both 
hands, you can effectively control the subsequent recoil motion. 

After long time of use, the cylinder case becomes hot.  Therefore, be careful 
not to burn your hands. 

Do

n’t apply big pressure on the machine.  The hammer mechanism is 

activated by applying a slight pressure on the tool when the chisel bit is in 
contact with the work-piece. 

In some cases, it is necessary to punch up the bit against the crushing 
position forcibly in order to begin the striking strokes.  This is not due to 
malfunction of the tool, it means that the safe guard mechanism against no-
load striking is working. 

8.5 

Hammer/drill switch 

The mode selector (6) can switch the hammer and hammer/drill functions. 

 

Hammer/ drill mode: 

Drill in masonry, concrete and natural stone.  
Don’t use the hammer drill function for ceramic tile or others material can not 
withstand impact energy. 

 

Hammer mode:  

Drill in masonry, concrete and natural stone.  

Summary of Contents for Powerplus POWX1190











Reviews: