background image

 

POWXG2016 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

12

 

www.varo.com 

Noise 

Noise emission values measured according to relevant standard. (K=3) 

Acoustic pressure level LpA 

88 dB(A) 

Acoustic power level LwA 

110 dB(A) 

ATTENTION! Wear hearing protection when sound pressure is over 85 dB(A). 

aw (Vibration): 

0,9 m/s² 

K = 1.5 m/s² 

14 SERVICE DEPARTMENT 

Damaged switches must be replaced by our after-sales service department. 
If the connecting cable (or mains plug) is damaged, it must be replaced by a special 
connecting cable which is available from our service department. Replacement of the 
connecting cable should only be carried out by our service department (see last page) or by 
a qualified specialist (qualified electrician). 

15 TROUBLE SHOOTING 

PROBLEM 

PROBABLE CAUSE 

CORRECTIVE ACTION 

Unit won’t start or 
starts but will not 
run.

 

 

Incorrect starting procedures. 

 

Incorrect carburettor mixture 
adjustment setting. 

 

Fouled sparking plug. 

 

Empty fuel tank. 

 

Primer bulb was not pressed 
enough. 

 

Follow instructions in the 
User Manual. 

 

Have carburettor adjusted 
by an Authorized Service 
Centre. 

 

Clean/gap or replace plug. 

 

Fill fuel tank with properly 
mixed fuel. 

 

Press primer bulb fully and 
slowly 10 times. 

Unit starts, but 
engine has low 
power.

 

 

Fuel filter is plugged. 

 

Incorrect lever position. 

 

Dirty spark arrester screen. 

 

Dirty air filter. 

 

Incorrect carburettor mixture 
adjustment setting service 
dealer. 

 

Replace the fuel filter. 

 

Move to RUN position. 

 

Replace spark arrester 
screen. 

 

Remove, clean and reinstall 
filter. 

 

Have carburettor adjusted 
by an Authorized Service 
Centre. 

Engine sputters. ! 

 

Incorrect carburettor mixture 
adjustment setting. 

 

Air filter is plugged. 

 

Old or improperly mixed fuel. 

 

Have carburettor adjusted 
by an Authorized Service 
Centre. 

 

Replace or clean the air 
filter. 

 

Drain gas tank/add fresh 
fuel mixture. 

No power under 
load.

 

 

Incorrect carburettor mixture 
adjustment setting. 

 

Old or improperly mixed fuel. 

 

Air filter is plugged. 

 

Fouled spark plug. 

 

Have carburettor adjusted 
by an Authorized Service 
Centre. 

 

Drain gas tank /add fresh 
fuel mixture. 

 

Replace or clean the air 

Summary of Contents for Powerplus GardenPro POWXG2016















Reviews: