background image

       

 

 

Thanks for purchasing a Solo Jib from 
VariZoom. This lightweight telescoping jib is very 
easy to set up and use, but because it’s a 
counterweighted system that elevates your 
camera, you must exercise caution when 
operating the Solo Jib. 

Without proper setup and 

operation, damage to the equipment and/or 
injury to the user and people around the 
equipment may occur. 

Included items: Solo Jib, mounting stud & hand 
knob for bowl-mount tripods, 5.5 lbs counter 
weight (“2.5kg”), bar fitting and nut/spacers for 
mounting counterweight, carrying bag. 

Watch the video: 

http://www.youtube.com/watch?v=M6dRv1vBr7g#t=52

 

1)

 

Never remove the camera or counterweights without the appropriate support to 
prevent the jib from swinging up or down. 

2)

 

Do not extend the telescoping sections of the jib while the camera is mounted. The 
weight of the camera might cause a section to slide suddenly and pinch your hands 
or even damage the camera. 

3)

 

Make absolutely certain that the jib is securely mounted to the tripod and leveled so 
no slipping or loosening can occur. Also make sure the tripod is adequately level and 
stable relative to the ground. 

4)

 

Tighten all joints thoroughly to prevent unwanted extension/contraction. 

5)

 

Never swing the jib around in a crowd of people. 

6)

 

Set up your camera and jib exactly as you intend to use it before going out on a 
shoot. The main factor to dial in is the amount of counterweight needed. Unless your 
camera is very small, to use the jib at its longest extension, you will need additional 
weights. Likewise, using the jib at its shortest may require smaller weights. Standard 
barbell plates with a 1” hole can be purchased at sporting goods stores. We 
recommend buying one each 1.25, 2.5, 5 and 12.5 lbs plate for maximum flexibility. For 
the maximum 7lbs load at the camera platform at full extension, you’ll need about 19 
lbs total. 

This manual covers both the aluminum and carbon fiber versions of the Solo Jib. Setup 
and Operation for both are identical, with the only substantial difference being the lighter 
weight of the carbon fiber version. If you have any questions or concerns about using 
your Solo Jib, please contact us 

[email protected]

 or call 512-219-7722. 

www.cvc.de

Summary of Contents for SoloJib








Reviews: