background image

VSD-1C 

Page 5 

Using the VSD-1C 

With the VSD-1C you can control a variable fan according to a 0-10 Volts or 4-20 mA 
input signal. Refer to figure 2 for the location of the different switches, jumpers and 
selectors of the module. 

Figure 2: Electronic Board and Component Location 

15A/250V

230V

FAN

LINE

115/230V

INPUT

1341 B

-

+

ON

OFF

1 2

MIN. SPEED

-

+

0-20mA

0-10V

JP1

 

 
1

Minimum Speed Potentiometer 

This potentiometer is used to adjust the Minimum Speed of the fan. This will be 
the minimum speed when the input signal is at its minimum value.

 

 
2

Dip Switches (Input Range and Shutoff 5%

Dip Switch 1 is used to select the Input Range (ON = 2-10 Volts / 4-20 mA, OFF 
= 0-10 Volts / 0-20 mA). 
Dip Switch 2 is used to adjust the output behavior when the input is below 5% of 
its total range (ON = Shutoff, OFF = Runs continuously at Minimum Speed). 

 
3

Input Type Jumper 

This jumper is used to select which input type is used. Two types of input can be 
used which are: 0-10 Volts (jumper on the 2 left pins) and 0-20 mA (jumper on 
the 2 right pins).

 

 

 

[

2

[

1

[

3

Summary of Contents for VSD-1C












Reviews: