Vari agatha DS-521, Translation Of The Original Instructions

Page: 30 / 68

Agatha
5) According
Pict.1
-put the rear (shorter) screen (7) on the shorter arm of the screen holder (2). Put the side (longer)
screen (7) on the longer arm of the screen holder (2). Put the clamp bands (2 pcs) through the holes in the screen holder and
draw both bands to fix both screens.
6) According Pict.2 - unscrew the fastening bolt (5) so that the side gate (2) can be easily pushed into the frame opening.
Tighten the fastening bolt with your hand and check that the side gate does not fall out spontaneously.
3.4.2 Putting into operation

The cutter may be delivered without the engine operating fluids (according to various national rules)!

First read the engine user manual
82
carefully! This way, you may avoid possible damage.
1. Check the engine oil level; fill the engine with prescribed type and amount of oil if necessary. Fill the tank with prescribed amount
and type of petrol.
2. Shift the accelerator lever into ‘ CHOKE ’ position. The accelerator lever positions are described in picture
Pict.4. All four described
main positions are locked by a simple stamp-projection system in the lever body.
DS-521Z : Press the PRIMER 2-3 times before starting the without preheating engine.
3. Start the engine by pulling the rope of the recoil starter
83
.
4. First let the new or cold engine run for about 30 sec with a choke (accelerator lever in ‘ CHOKE ’ position) and then shift the
accelerator lever into ‘ MAX ’ position. Let the engine run in this position for about 30 sec.

Do not go away from the machine!

When starting the engine, both control levers (1 and 2 in Pict.2) must be in the position turned off (they must not
be pushed to the handlebars)!
3.4.2.1 Starting up the cutting disc

Make sure that all persons, animals and children are at a safe distance from the machine! If they are not, do not
continue in your activity!
1. Start the engine
84
.
2. Use the accelerator lever to set the maximum engine speed. (In case the engine is cold, warm it up at maximum speed for about
1 minute)
3. Take hold of the handlebars handle with your left hand. With your right hand then slowly push the lever ( 1 in
Pict.2) on the right
handle.

Slowly press the lever up to about two thirds throttle, to start up the cutting disc and prevent the engine
form turning off.
4. After starting up the cutting disc, press the lever to the handle and hold firmly.

The cutting disc start-up is accompanied by V-belt creeping and its side effects (chattering, whistling).
These effects usually disappear when the V-belt is run-in.
Note:
During the first starts of the cutting disc, a new or cold engine might stall. This tendency disappears after warming up the engine. In
case the cutting disc drive cannot be runned up, check if there is a defect according to Table 8 .
3.4.2.2 Putting the machine in motion
To put the machine in motion use lever ( 2 in Pict.2) on the left handle. Press the lever all the way to the handle, and the machine
moves ahead immediately. Adjust the speed of your walk to machine speed as soon as you press the lever and the machine moves.
The wheel drive has a belt clutch; you can press the lever slowly and the machine starts off fluently, not with a jump.

Always press the clutch lever all the way down to the handlebars. If the lever is not pressed properly, it
causes damage to the V-belt.

The wheel drive clutch lever does not adjust travelling speed!

Never reverse with the wheel drive clutch pressed!
3.4.2.3 Machine stopping
If you wish to stop the machine, release the left handlebar lever. The machine stops moving, but the cutting disk spins. The cutting disc
drive is turned off by releasing the right handlebar lever. The cutting disc is stopped by an automatic brake. Shift the accelerator lever into
MIN or STOP position.

Always switch off the engine and wait for the cutting disk to stop before starting any activity near the machine!
Always switch the engine off before leaving the machine!
82 Multilingual manual and its Czech translation are part of the cutter.
83 Engine starting instructions are described in detail in engine user manual.
84 Engine starting instructions are described in detail in engine user manual.
33
R
ev
iz
e
0
4
/2
0
1
5