Vari Adela PRO BDR-720, Translation Of The Original Instructions, Page: 47 / 84

BDR-720 Adela PRO
3.4.6 C
ONNECTION OF THE
S
ULKA
AV-650

Never use the machine with the attached Sulka AV-650 on any slopes!

Observe this safety command, especially when working on land where combinations of planes and slopes occur. They can
easily overturn the set, e.g. when turning or if the side tilt of the set suddenly increases due to uneven terrain!
•
Fig. 12
Slide the fork of the Sulka drawbar over the hinge feet on the tubular bumper and secure the fork from above with a pin with a
locking pin.
•
The Sulka AV-650 machines feature their retractable drawbar, by extending the drawbar, set the distance of the sulky seat from the
machine, so that you can reach the travel control levers and turn on the cutting disc on the handlebars when turning left with the
necessary reserve of distance.
•
Adjust the handlebars to such a height that the handlebars do not collide with the lower limbs when the front of the machine is raised
by approx. 20 cm.
3.5 M
AINTENANCE AND
S
ERVICE
I
NSTRUCTIONS

Owing to the weight of the machine, all the maintenance and adjustment shall be performed by two people.
To secure a long-term satisfaction with our product, it is necessary to provide it with due care and maintenance. By providing regular
maintenance you will prevent its rapid wear and you will secure correct operation of all its parts.
Observe all instructions concerning maintenance and adjusting intervals. We recommend that you keep records of operating hours and
the conditions under which the machine is used (these may be useful for servicing centres). We recommend that you have the post-season
maintenance implemented by one of our authorized service centres; the same applies to standard maintenance if you are not certain of
your technical capabilities.

The good help to monitor operating hours is the VARI PowerMeter device. This accessories can be bought with every
dealer of VARI products.

Due to the high proportion of BIO components in the fuels, we strongly recommend that you drain all the fuel from the
carburettor before each shutdown of the machine - close the fuel valve and let the engine run until it switches off
spontaneously.

Before any use of the machine, check the tightening of its screws securing the blades in the upper disc and also
the screws securing the lower disc to the flange.

Replace the lost screwed connections with the original parts that are designed for the given spot. By using
unoriginal low-quality parts, you expose yourself to the risk of injury or damage to the machine!
3.5.1 R
ECOMMENDED
T
OOLS AND
A
CCESSORIES
For the assembling and maintenance of your machine, we recommend the following tools and accessories
81
-
Fig. 27
on page
81
.
TOOLS ACCESSORIES
Spanner No. 8 mm - 1x Petrol can, capacity 5 litres, HONDA - Ord. No. 4359
Spanner No. 10 mm - 2x HONDA fuel stabiliser - Ord. No. 08CXZ-FSC-250
Spanner No. 13 mm - 2x Briggs & Stratton Fuel Fit™ fuel stabiliser - Ord. No. 992381
Allen spanner No. 5 - 1x Hour meter VARI POWERMETER - Ord. No. 4227
Curved ratchet 3/8 “+ 12-square socket head 15 mm and 16 mm - 1x Spare blades set - Ord. No. 1005900200
82
Spark plug wrench 16 mm - 1x
Table 35: Recommended Tools and Accessories
81
The tools and accessories are not included in the delivery of the machine, they must be purchased separately.
82
The set includes 5 blades, incl. screw connection, because the set is common for the machine RBS-700, which has five blades. For the BDR-720 machine, use only 4 pieces from the
set, you can save the remaining 1 piece for future use. However, never change only one blade due to the different weights of new and worn blades!
47
R
ev
iz
e
0
7
/2
0
2
1