background image

8

VL3600 PROFILE IP

 

Quick Start Guide

 REV A 06/28/22

DMX 

CHANNEL 

PARAMETER

1

intensity High

2

intensity Low 

3

Pan High

4

Pan Low

5

tilt High

6

tilt Low

7

Focus High

8

Focus Low

9

Zoom High

10

Zoom Low

11

cyan

12

Yellow

13

Magenta 

14

ctO Wheel

15

color adjustment

(color Wheel 2)

16

color Wheel 1

17

color Wheel 1 control 

18

Gobo Wheel 1 (Fixed)

19

Gobo Wheel 1 control

20

Gobo Wheel 2

21

Gobo Wheel 2 rotate/index 

High Byte

22

Gobo Wheel 2 rotate/index 

Low Byte

23

Gobo Wheel 2 control

24

VLFX (Gobo Wheel 3)

25

VLFX (Gobo Wheel 3)  

rotate/index High Byte

DMX 

CHANNEL 

PARAMETER

26

VLFX (Gobo Wheel 3)  

rotate/index Low Byte

27

VLFX (Gobo Wheel 3)  

control

28

iris

29

Frame 1a

30

Frame 1B

31

Frame 2a

32

Frame 2B

33

Frame 3a

34

Frame 3B

35

Frame 4a

36

Frame 4B

37

Frame rotate

38

Prism 1 (triangular)

39

Prism 1 index/rotate High 

Byte

40

Prism 1 index/rotate Low 

Byte

41

Prism 2 (Flat)

42

Prism 2 index/rotate  

High Byte

43

Prism 2 index/rotate  

Low Byte

44

Frost

45

Strobe

46

Future use channel

47

Programmers channel

48

Fan control

49

Luminaire control

TAbLE 2. 

16-bIT MODE

Quick reFereNce dMX MaPS

The short form DMX maps are available on the following pages. Visit the product page for full DMX maps.
• 

table 2. 16-Bit

• 

table 3. 16-Bit enhanced Mode (default)

Summary of Contents for 74817-001












Reviews: