ASSEMBLING THE MR-500 VENTO
Fig.1
GO TO VAPAMORE.COM TO SEE THE MR-500 VENTO INSTRUCTIONAL VIDEO
Fig.2
1
Fig.3
Push down
to lock in
place
VACUUM HOSE AND HANDLE
With the hose pointed towards the rear of the vacuum, push
its locked into place. To remove the connector push in the
release buttons located on both sides of the connector and
pull up to release. NOTE: The hose contains electrical wires
and should not be used if damaged or if wires are exposed in
any way through the outer shielding. Fig.1
switch operated electric rotating brush to be used for carpets and rugs plus a non electric
the non electric extension pole or directly with the hose handle.
MIN
MAX
Release
buttons
on sides
ELECTRIC EXTENSION POLE AND FLOOR HEAD
Attached the hose handle into the electric extension pole by
locked into place. To remove the handle push in the release
button and pull upward. To extend or collapse the extension
pole, push downward or pull upward as directed by the
arrows on the extension handle. Fig. 2
pull up on the electric extension pole to release. Fig. 3
NON ELECTRIC EXTENSION POLE, FLOOR HEAD AND TOOLS
Attached the hose handle into the non electric extension pole
Fig.4
used with the non electric extension pole or directly to the
hose handle.
tools are attached in the same manner by pushing the non
of the vacuum to rotate the internal brush. Fig. 5
Push all
tools down
to lock in
place
Hose handle
Non electric
pole
Push down
to lock in
place
Release
petal
to extend and collapse the extension pole . Fig. 4
Release
button
Push down
to lock in
place
Push up
or down
to extend
or collapse
push button
to extend or
collapse pole
Push down
until snug
Fig.5
e
e
e
e
e
e
Once you have assembled the vacuum, pull the power
cord out and plug into a standard outlet. Never pull the
power cord past the marked stop point as this may
damage the auto re winder. Retract the power cord by
pressing the petal until the cord is fully rewound. Fig. 6-7
USING YOUR MR-500 VENTO
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11]
GO TO VAPAMORE.COM TO SEE THE MR-500 VENTO INSTRUCTIONAL VIDEO
2
1
3
OPERATION
Turn the vacuum on by pressing the on/off petal. To turn
the vacuum off press the petal again. Fig. 6-7
Once the vacuum is turned on you can adjust the variable
suction settings by pushing the plus (+) or minus (-)
buttons located on each side of the control panel. This
allows you to adjust for low suction for delicate surfaces
like drapery all the way to the maximum suction for deep
carpets. When vacuuming rugs use a setting 1 to 2 under
maximum as most rugs have rubber backing and will not
allow the vacuum to breath properly. Using to high of a
setting on rubber backed or flow restricted areas can
damage the vacuum motor or drive belt. Fig. 7
The filter bag full indicator light will turn red when the filter
bag is full and needs replacing. There are three conditions
that will cause the indicator light to come on. 1,The filter
bag is full and needs to be replaced. 2, Very fine powder
has clogged the pores in the filter bag even if not
completely full it must be replaced. 3, There is a clog in
the nozzle, hose, tools, or at the filter bag opening that
must be cleared. Note: The filter bag full indicator is
designed to notify the user when the filter bag is full. If
the filter bag is full of pet hair, carpet fibers, or any loose
light fibers the bag full indicator may not light up due to
sufficient air flow in the filter bag. Discard the full filter bag
and replace with a new one. Fig. 8
FILTER BAG
The filter bag must be maintained to keep the vacuum
operating at maximum efficiency. Change the filter bag
frequently or when the filter bag full indicator comes on.
To replace the filter bag, first disconnect the vacuum hose
from the vacuum by depressing the two buttons on each
side of the hose connector. Then lift the filter bag
compartment latch and open the lid. Fig. 9
Before removing the filter bag pull on the tab “A” to seal
the filter bag and keep dust from escaping as the filter
bag is changed. Then pull the filter bag out and discard.
Fig. 10
Replace with a new filter bag by sliding the bag into
the bag retainer in the direction of the arrow located on
the filter bag. Once the filter bag is in place, close the lid.
Fig. 11
MIN
MA
X
On/Off
Power cord
re winder
Max
suction
Min.
suction
On/Off
Power
cord
re winder
Filter bag
full indicator
Filter bag
compartment
latch pull up
