Vanguard VN6D Owner'S Operation And Installation Manual Download Page 11

11

104274

OWNER’S MANUAL

TO SELECT

HEATING LEVEL

1.

Slightly press in control knob and
turn counterclockwise 

 to the

LOW or HIGH positions (VN10A) or
ON position (VN6D).

IMPORTANT:

 Release downward

pressure while turning control knob.
Control knob will lock at the desired
position.

Figure 17 - Burner Patterns

 WARNING: When running

heater, set control knob at LOW
or HIGH locked positions (VN10A)
or ON position (VN6D). Never set
control knob between locked
positions. Poor combustion and
higher levels of carbon monox-
ide may result.

OPERATING
HEATER

Continued

 CAUTION: Do not try to adjust

heating levels by using the equip-
ment shutoff valve.

Control

VN10A

Knob

Burners

Control

VN6D

Knob

Burner

LIGHTING

INSTRUCTIONS

1.

STOP! Read the safety information,
page 10, column 3.

2.

Make sure equipment shutoff valve
is fully open.

3.

Turn control knob clockwise 
to the OFF position.

OFF

PILOT

IGNITOR

LOW

HIGH

Piezo Ignitor Button

Figure 15 - Control Knob In The OFF
Position (Model VN10A Shown)

Control Knob

4.

Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety in-
formation, page 10, column 3. If you
don’t smell gas, go to the next step.

5.

Press in control knob, and turn coun-
terclockwise 

 to pilot posi-

tion. Keep control knob pressed for
five seconds.

Note:

 You may be running this

heater for the first time after hook-
ing up to gas supply. If so, the con-
trol knob may need to be pressed in
for 30 seconds. This will allow air to
bleed from the gas system.
• If control knob does not pop up

when released, contact a qualified
service person or gas supplier for
repairs.

6.

With control knob pressed in, push
down and release ignitor button. This
will light pilot. The pilot is attached to
the front of burner. If needed, keep
pressing ignitor button until pilot lights.

Note:

 If pilot does not light, refer to

Troubleshooting, pages 13 through
15. Also contact a qualified service
person or gas supplier for repairs.
Until repairs are made, light pilot
with match. To light pilot with match,
see Manual Lighting Procedure
.

7.

Keep control knob pressed in for 10
seconds after lighting pilot. After 10
seconds, release control knob.

Note:

 If pilot goes out, repeat steps

3 through 7.

Ignitor Electrode

Pilot Burner

Thermocouple

Figure 16 - Pilot

Shutting Off Heater

Turn control knob clockwise  

 to

the OFF position.

Shutting Off Burner Only (pilot
stays lit)

Turn control knob clockwise 

 to

the PILOT position.

TO TURN OFF GAS

TO APPLIANCE

MANUAL LIGHTING

PROCEDURE

1.

Remove front panel (see Figure 10,
page 8).

2.

Follow steps 1 through 5 under Light-
ing Instructions
.

3.

With control knob pressed in, strike
match. Hold match to pilot until pi-
lot lights.

4.

Keep control knob pressed in for 10
seconds after pilot is lit. After 10 sec-
onds, release control knob.

5.

Replace front panel.

LOW

OFF

PILOT

HIGH

OFF

PILOT

OFF

ON

OFF

PILOT

OFF

Summary of Contents for VN6D





















Reviews: