Vanderbilt VR20M-MF User Manual Download Page 5

Page: 5 / 30

2 Technical data

VR20M-MF Mifare card reader
standard

VR50M-MF Mifare card reader
standard with keypad

Protocol

OSDP or Wiegand

Interface to controller

RS485 or Wiegand

Operating voltage

8.5 – 30.0 VDC

Power consumption

DC 12V 50mA Peak 150mA
DC 24V 35mA Peak 100mA

Tamper protection

Yes

Card technology

Mifare

Card compatibility

Mifare Classic

Mifare Plus

Mifare DESfire EV1/ EV2

Mifare Classic

Mifare Plus

Mifare DESfire EV1/ EV2

Reading distance

Mifare Classic-up to 6 cm

Mifare Plus-up to 6 cm

Mifare DESfire EV1/ EV2-the
card must be held to the reader

Mifare Classic-up to 6 cm

Mifare Plus-up to 6 cm

Mifare DESfire EV1/ EV2-the
card must be held to the reader

Indicators

3 x LED (red/yellow/green)

1 x Buzzer

Multicolour light frame

3 x LED (red/yellow/green)

1 x Buzzer

Multicolour light frame

Keypad

Yes

Operating temperature

- 40°C to + 70°C

IP rating

IP55

IK class

Housing

Zinc casted metal bezel with
polycarbonate plastic front

Color

Black, matt chrome

Dimensions (WxHxD) mm

Surface mounted: 48 x 129 x 22

Surface mounted: 48 x 129 x 24

Approvals

CE 2014/53/EU

A-100410

21.06.2018

Summary of Contents for VR20M-MF































Search results

Summary of Contents for VR20M-MF

Reviews:

Related manuals for VR20M-MF

Brands by name

Popular brands

Vanderbilt VR20M-MF, User Manual

Search results

Summary of Contents for VR20M-MF

Reviews:

Related manuals for VR20M-MF

Brands by name

Popular brands