V&A M266 Series User Manual Download Page 12 | Manualshive

Page: 12 / 12

background image

5 ACCESSORIES

5.1 SUPPLIED WITH THE MULTIMETER

  Test Leads
  Battery
  Operating Manual

5.2 OPTIONAL ACCESSORY

“

K

”

type thermocouple

INSULATION TESTER UNIT 261

6 BATTERY REPLACEMENT

If the sign

“

BAT

”

appears on the LCD display, it indicates that battery should

be replaced. Remove the battery cover of case. Replace the exhausted battery with a
new one.

WARNING

Before attempting to open the battery cover, be sure that test leads have been
disconnected from measurement circuits to avoid electric shock hazard.

M

266

-09

«
...
10
11
12

Summary of Contents for M266 Series













Reviews:

No comments

Related manuals for M266 Series

Brand: BANTE inststruments Pages: 15

Brand: 3Bays Pages: 21

Brand: Eaton Pages: 87

Brand: Eaton Pages: 16

Brand: ECO Sensors Pages: 22

Brand: ECO Sensors Pages: 7

Brand: F&F Pages: 24

Brand: Lumel Pages: 32

Brand: R&S Pages: 733

Brand: R&S Pages: 369

Brand: Cecomp Pages: 4

Brand: Rae Pages: 38

Brand: FlowLine Pages: 2

Brand: TA Instruments Pages: 68

Brand: Omicron Pages: 76

Brand: Galileo Pages: 30

Brand: Hach Pages: 4

RLACS277RLACS29

Brand: Racelogic Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands