background image

---9---

B. Safety precautions

B 1.1.

Roll Over Protective Structures

A B1

Fig. 5
A Roll Over Protective Structure (ROPS) and seat belt

(extra equipment) is fitted as standard equipment to the

footstep tractor at the time of factory assembly. If the

ROPS was removed by the original purchaser or has been

removed, it is recommended that you equip your tractor

with a Roll Over Protective Structure and a seat belt.

ROPS are effective in reducing injuries during overturn

accidents. Overturning a tractor without ROPS can result

in serious injury or death (Fig. 5).
If a fold down ROPS is installed DO NOT wear seat belt

when the ROPS is in the folded down position.

B 1.1.1.

Operation

--- Before using the tractor ensure that the ROPS frame is

not damaged, that it is securely fastened to the tractor

and if a hinged section is fitted that it is in the raised

position and secured.

--- If the ROPS has been removed from the tractor, or fol-

ded down for a specific operation, it must be refitted or

erected immediately afterwards using the proper hard-

ware and applying the recommended torque values.

--- DO NOT attach chains, ropes, or cables to the ROPS for

pulling purposes; this will cause the tractor to tip back-

wards. Always pull from the tractor drawbar.

--- Always wear your seat belt --- adjusted snugly except

when operating with a folded down ROPS.

AB2

Fig. 6

--- Check the seat belt for damage. A damaged seat belt

must be replaced (Fig. 6).

B 1.1.2.

Damage to the ROPS

If the tractor has rolled over or the ROPS has been

damaged (such as striking an overhead object during

transport), the ROPS must be replaced to provide the

original degree of protection.
After an accident, check for damage to the ROPS,

operator’s seat, seat belt and seat belt mountings. Before

you operate the tractor, replace all damaged parts.
DO NOT WELD, DRILL, BEND OR STRAIGHTEN THE

ROPS . To do so reduces the protection it offers.

B 1.1.3.

Sun protection roof

A B3

Fig. 7

--- ROPS, FOPS (Falling Object Protective Structure),

protective enclosure or protective screens (Fig. 7).

Remember FOPS are protection from light falling

objects and are not intended as protection from large

falling objects such as large round bales or fence rails.

--- SMV (slow moving vehicle) emblem, additional safety

guards, lights or decals and a back up alarm.

Summary of Contents for A75l




















Reviews: