background image

13

1.  Measure from range top to hood bottom and mark line A.  

(26” minimum from range top) .

2.  Plum and mark center line.

3.  Mark mounting height line B. (15-3/8” from line A)

4.  Mark mounting spread from C/L. (8-7/8”) 

5.  Fasten (2) M4 x 1-1/2” screws into studs on line B but 

do not tighten all the way.  

Note: wood blocking may 

need to be added behind the drywall if no studs are 
present.  Wall anchors may also be used but check 
local codes for compliance. Failure to use suitable 
wall anchors and screws to hold the weight of the 
hood could result in personal injury or damage to 
cooking sureface or counter.

6.  Remove the (2) metal mesh fi lters.

7.   Remove the (2) charcoal fi lter brackets located inside 

the hoood behind the metal mesh fi lters.  Each bracket is 
secured with (4) 3/16 x 6 Philips head screws.

Note: If 

you are not recirculating the hood you may discard 
the charcoal brackets.

8.  Hang hood onto the mounting screws and hand tighten 

each screw. (fi g A) Secure third M4 x 1-1/2” screw 
through inside of hood into wall for extra support. (fi g A2) 

9.  Center and attach duct cover mounting bracket to wall 

just below the ceiling or soffi t using (2) M4 x 1” screws.

10. Install electrical and duct work.  Seal duct work with 

aluminum duct tape.

11. Power up hood and check for leaks around duct tape.

12. Place telescopic duct covers onto hood and extend 

inner (top) duct cover upwards and secure to duct cover 
bracket using (2) M3.5 x 8 screws. Secure bottom duct 
cover to hood body by also using (2) M3.5 x 8 screws.

* If using hood in recirculating mode you must secure the air 

diverter plate onto wall before installing duct work and 
duct covers.  Turn to page 14 for more details.

15-3/8

Brackets are 

pre-installed

fig. A

fig. A2

26” min

CAUTION: At least two installers are

required due to the weight and size of the
hood.

!

WARNING: Electrical wiring must be done by a qualified person(s) in

accordance with all applicable codes and standards. This range hood must be
properly grounded. Turn off electrical power at service entrance before wiring.

!

Cable Lock

Cable Lock

A cable locking connector (not supplied) might 
be required by local codes.  Check with local 
requirements and codes, purchase and install 
appropriate connector if necessary.

Installation – 

Mounting the Hood VCR

Summary of Contents for VCR-E30AG
























Reviews: