background image

15

 

16

 

 

PART FIVE Trouble Shooting

 

 

 

1. If the display unit does not receive signals properly from a sensor in 20 minutes, the system will show

 

“---” on the corresponding location in the display.

 

2.  Sometimes  you  may  see 

“  ---”  when  the  vehicle  is  parked.  This  might  be  caused  by  the

 

surrounding interference. 

This is normal. The display will show correct data when you run the vehicle.

 

3. Try to avoid parking the vehicle under strong sunlight. The LCD screen may be damaged after one hour

 

of exposure to 70°C (158°F) in-car temperature.

 

 
 
 

PART SIX Parameters of the Product

 

 

 

 

Transmitter

 

Weight: 35 g (1.25 oz.)

 

Dimensions: 6.4 x 2.8 x 1.5 cm (2.52 x 1.10 x

 

0.59 inch)

 

Operating  Temperature  Range*:  -40  °C  to  85

 

°C

 

(-40 to 185 °F)

 

Pressure Accuracy: ±0.15 Bar (2 PSI)

Temperature Accuracy: ± 3 °C (5.4 °F)

Maximum Range: 5.9 Bar (85 PSI)

Frequency: 433.92MHz

 

*-40 °C to 125 °C is available upon request.

 

 

Display

 

Power    Consumption:    130    mW    (Regular);

 

230mW (Max)

 

Power Supply: DC12 Volt

 

Weight: 75 g (2.65 oz.)

 

Dimensions: 7.7  x 4.9  x  2.2  cm (3.03  x  1.93  x

 

0.87inch)

 

Operating Temperature Range: -20 °C to 70 °C

 

(-4 to 158 °F)

 

Pressure Resolution: ±0.01 Bar (0.1 PSI)

 

Temperature Resolution: 1 °C (1 °F)

 

 

Problem

 

 

Possible Reasons

 

 

Solution

 

 
 
 

"000" shows on

 

the display

 

First use of TPMS, need, to

 

verify installation

 

Run vehicle at speed of 25 km/h

 

at least, see 2.6

 

 
 

 

No signal

 

Make sure right installation position of

 

transmitters and ID modules, see 2..4.2

 

 

Change 

display’s position, see 2.1

 

 

Nothing shown on

 

the display

 

 

Switch of display is off

 

Use dual long antenna, see 2.2

 

Power cord is not properly

 

installed

 

Check power cord connection,

 

see part four of Installation Manual

 

"000" shows on

 

the display

 

 

System failure

 

Restart the system, see 4.1

 

 
 
 
 
 

dash - - - shows

 

on the display

 

 

 

ID module is not properly

 

connected with display

 

Pull out the ID module and re-plug

 

in, see 4.3;

 

Then restart the system, see 4.1

 

ID module checkout, see 4.6

 

 

 

Receiver did not

 

receive the signal from

 

the transmitter

 

Transmitter or ID

 

module failure

 

 

Change 

display’s position, see 2.1

 

Use dual long antenna, see 2.2

 

 

Contact your distributor

 

Data does not

 

refresh

 

 
 
 
 

 

System failure

 

 
 
 
 
 

Restart the system, see 4.1

 

Back light does

 

not turn off

 

 

The display

 

continues to show

 

incomprehensible

 

codes

 

 

Summary of Contents for TPMS201DX













Reviews: