background image

State of California. Proposition 65 Warning. 

Fuels used in gas, wood-burning or oil fired appliances, and the 

products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth 

defects and other reproductive harm. California Health & Safety Code Sec. 25249.6.

State of Massachusetts Carbon Monoxide Detector/Vent Terminal Signage Requirements

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used 

in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where 

the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, 

including but not limited to decks and porches, the following requirements shall be satisfied: 

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal 

vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide 

detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. 

In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide 

detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side 

wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the 

services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, 

the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor 

level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the 

owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during 

said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance 

with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified. 

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at 

a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally 

vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch 

in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not 

approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage 

installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4. 

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4: 

1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of 

NFPA 54 as adopted by the Board; and 

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate 

from the dwelling, building or structure used in whole or in part for residential purposes. 

Safety and Warning Information

Summary of Contents for Portrait 530ICN/ICP





































Reviews: