Valor Legend G4 Series Installation Instructions Manual Download Page 3

Set and check manifold pressure and 
aeration

Set the manifold pressure.
1.  Remove the valve access panel (5 screws) on the 

left hand side of the appliance case. If the appliance 
is already installed, you will need to pull the left 
hand side out of the cavity.

2.  Fit a manometer to the 

manifold pressure test 
tap on the valve—see 

fi

 gure at right. 

3.  Light the appliance and 

turn the control to full 
input. 

4.  Adjust the pressure 

adjustment screw using 
a small jeweller’s size 

fl

 at 

blade screwdriver—as 
shown below—while 
the appliance is running 
at full input to produce 
manifold pressure, as per 

Speci

fi

 cations 

table on page 1.

Manifold Pressure 
Test Tap

Valve Inlet 
Pressure

Loosen screw to check 

(tighten afterwards)

Pressure Test Tappings

Front Face of 
Control Valve

Pry off 
plastic cap

Front Face of 
Control Valve

Pressure
adjustment
screw behind
plastic cap

Increases pressure

Decreases pressure

5.  Check the aeration and adjust the air shutter if 

necessary.

6.  Turn off the appliance, remove the manometer and 

tighten the test tapping screw. Check for leaks.

7.  Fit the label 

“This control has been converted...”

 on 

the left hand side of the appliance near the valve.

8. Re

fi

 t the valve access panel (5 screws).

Add baf

fl

 e to rear log support 

(when 

converting to 

LPG only

)

Fix the secondary air baf

fl

 e provided to the underside 

of the rear log support with 4 screws provided as 
indicated. The baf

fl

 e can also be riveted to the support 

from the top.

0B293

6 mm

AERATION GAP

Flashback 

shield

LPG Air Shutter 

Slider

Open

Close

LPG

Open

Open

Close

Close

NG

NG Air Shutter 

Slider & Cover

6 mm

Valve

3

Summary of Contents for Legend G4 Series









Reviews: