Valor L1 Series Installation Manual Download Page 3

5. Once wall 

fi

 nishing is complete, place cover plate in 

the bottom of the opening. It will rest on the sup-

ports at the bottom corners of the opening. There 

are no screws inserted in this step.

Notes:

- The opening in the cover plate should be oriented 

as shown below to allow air to enter while obstruct-

ing any view through its opening.

- Each end of the plate has rounded notch opening 

to insert the hinge pin of the side doors.

6.  Identify left hand door and its orientation according 

to the images below.

7.  Insert the left hand door top hinge pin in the hole at 

the top of the CIK frame, then the bottom hinge in 

the hole of the cover panel. Turn the door in toward 

the back of the 

fi

 replace.

8.  Repeat for right hand door.
9.  Place the magnetic barrier screen into the CIK frame 

opening with the tabs at the bottom.

Assembly of the kit is complete.

TOP of door:
this space is
wider

TOP of door:
tab at the rear

Left door

BOTTOM of door:
this space is
narrower

Rear view

Front view

Top pin

Bottom pin

Cover plate

Opening in 

cover plate

3

Summary of Contents for L1 Series









Reviews: