Valor G3 739 Owner'S Manual Download Page 5

5

Safety and your fireplace

Glass window

• The glass front assembly must be in place and sealed 

before the unit can be placed into safe operation.

• The glass front assembly must only be replaced as a 

complete unit, as supplied by the 

fi

 replace manufac-

turer. No substitute material may be used.

• Do not use abrasive cleaners on the glass front as-

sembly. Do not attempt to clean the glass when it is 

hot.

Venting

• This unit must be used with a vent system as de-

scribed in its installation manual. No other vent 

system or components may be used.

• Never obstruct the 

fl

 ow of combustion and ventila-

tion air. Keep the front of the appliance clear of all 

obstacles and materials for servicing and proper 

operation.

• This gas 

fi

 replace and vent assembly must be vented 

directly to the outside and must never be attached 

to a chimney serving a separate solid fuel burning 

appliance. Each gas appliance must use a separate 

vent system. Common vent systems are prohibited.

Intended use 

• This appliance is designed and approved as a supple-

mental heater and provides the potential for most 

energy conservation when used while attended. The 

use of an alternate primary heat source is advisable.

• This unit is not for use with solid fuel.

• Do not use this heater as a temporary source of heat 

during construction.

Installation and Servicing

• Installation and repair should be done by a quali

fi

 ed 

service person. The appliance should be inspected 

before use and at least annually by a professional 

service person. More frequent cleaning might be 

required due to excessive lint from carpeting, bed-

ding material, et cetera. It is imperative that control 

compartments, burners, and circulating air passage-

ways of the appliance be kept clean.

• Do not use this appliance if any part has been under 

water. Immediately call a quali

fi

 ed service technician 

to inspect the appliance and to replace any part of 

the control system and any gas control that has been 

under water.

Maintenance

• Keep the unit’s control compartment, burner, and 

circulating air passageways clean to enable adequate 

combustion and ventilation air.

• Inspect the external vent cap on a regular basis to 

ensure that no debris, plants, trees, or shrubs are 

interfering with air 

fl

 ow. 

WARNING

Do not operate this appliance with the 

glass front removed, cracked, or broken. 
Do not strike or slam the glass front.
Replacement of the glass front should 

be performed by a licensed or quali

fi

 ed 

service person. 

Summary of Contents for G3 739



























Reviews: