background image

 

7.4.  Switch to front frame installation 

7

.4.1  Thread the switch wires through the rocker switch mounting bracket. 

Snap fit the switch to the bracket with the switch positioned so that the 

terminals with two soldered wires are at the bottom when the two legs 

of the bracket are at the left side when viewed from the front – See fig. 

10. This will ensure that pressing the top of the rocker switch raises the 

flame setting. 

 

Fig. 10 

 

7.4.2  Fit the switch mounting bracket to the top left side of the front frame 

with the bracket legs in the slot in the frame – See fig. 11. 

7.4.3  Fit the rocker switch heat shield over the switch and bracket. Align the 

holes in the shield with those in the bracket and secure with two 

thread forming screws – see figure 12. 

 

 

Fig. 11 

 

7.5.  Optional trim installation 

7.5.1  #785 Brass trim – See fig. 13 

 

Fit the top, left and right side trims over the front frame. Align the holes in the 

frame and trims. Secure with the spring fasteners using four across the top and three 

each side. The flat face of the fasteners should be on the outside. 

 

  

 
 
 
 

 

Fig.12 

 

 

 

Fig. 13 

 

 

12

Summary of Contents for 737XN























Reviews: