Valor 700 Operating Instructions Manual Download Page 6

6

SETTING PROGRAM TIMERS

•• 

You can program two periods of time between 12:00 
am and 11:50 pm in each 24-hour cycle.

•• 

The Programs P1 and P2 must be set in the 
following order during a 24-hour cycle:           ,         ,            
            and         . 

•• 

The icon      indicates the beginning of the period (ON) 
and the icon     indicates the end of the period (OFF).

•• 

If            =           or            =         , the programming 
is cancelled.

•• 

To keep the 

 replace ON all night, set            at 

11:50 am and             at 12:00 am.

Default settings:

Program 1:              6:00 am             8:00 am
Program 2:            11:50 pm            11:50 pm

•• 

Brie

 y press SET button to scroll to 

TIMER mode.

•• 

Hold the SET button until                                      
(sun) is displayed and the time 

 ashes.

•• 

Brie

 y press SET button to scroll 

to TIMER           (moon) while the 
time 

 ashes.

•• 

Press         (large 

 ame) button to 

set the hour.

•• 

Press      (large 

 ame) button to set 

the hour.

•• 

Press      (small 

 ame) button to 

set the minutes.

•• 

Press      (small 

 ame) button to 

set the minutes.

SETTING P1 ON TIME

SETTING P2 ON TIME

•• 

Brie

 y press SET to scroll to TIMER mode           

(sun) while the time 

 ashes.

•• 

Follow the instructions given to set P1 ON time.

SETTING P2 OFF TIME

•• 

Brie

 y press SET to scroll to TIMER mode           

(moon) while the time 

 ashes.

•• 

Follow the instructions given to set P1 OFF time.

Press OFF button to save these settings. The timers 
are programmed. See the diagram on programming 
sequences on the following page.

Tip

If you want to program only one period, program           
and            with desired times and program            and
          with the same time as          .

SETTING P1 OFF TIME

P1

P1

P1

P1

P1

P1

P2

P2

P2

P2

P2

P2

P1

P1

P1

P1

P1

P1

P2

P2

P2

P2

P2

Summary of Contents for 700








Reviews: