Valor 203 Installation Manual Download Page 3

Page: 3 / 13

INSTALLATION GUIDE – 203 DISPLAY

www.valortpms.com

Table of Contents

Part 1: System Installation

1.1 Straight Truck/Tractor Installation

....................................................................................................................

1.2 Mounting Integrated Display

............................................................................................................................

1.3 Installing ID Modules

......................................................................................................................................

1.4 Installing TPMS Sensors

................................................................................................................................

1.5 Installing Antennas

..........................................................................................................................................

1.6 Trailer Installation

...........................................................................................................................................

1.7 Installing Tractor ID Box

.................................................................................................................................

1.8 Installing Gen II Trailer Box

.............................................................................................................................

1.9 Programming Gen II Trailer Box

......................................................................................................................

1.9.1 Installing Antennas

..........................................................................................................................................

Part 2: System Programming

2.1 Turning Integrated Display ON/OFF

..............................................................................................................

2.2 Programming Tire Pressure Baseline

............................................................................................................

2.3 Programming Date & Time

............................................................................................................................

Part 3:

Reading Integrated Display

3.1 Reading the Display

.....................................................................................................................................

3.2 Switching between Pressure and Temperature

.............................................................................................

3.3 Switch between Axles

....................................................................................................................................

Summary of Contents for 203














Search results

Summary of Contents for 203

Reviews:

Related manuals for 203

Brands by name

Popular brands

Valor 203, Installation Manual

Search results

Summary of Contents for 203

Reviews:

Related manuals for 203

Brands by name

Popular brands