background image

 

3

   

 

A.  Operating Instructions 

 
 

 

NOTE:   IT IS RECOMMENDED THAT ALL OPERATORS FAMILIARIZE THEMSELVES  

   WITH THE MACHINE AND DEVELOP SAFE WORKING HABITS. 

 
 
1. 

IMPORTANT!   Remove solid plug on hydraulic reservoir and install breather cap        
(included in the Power Pak) for proper air venting. 

 
2. 

Install battery with the negative pole on the left hand side (do not allow ground wire to 
come in contact with any other wires or a short will occur). 

 
3. 

Loosen rotator straps in the following way.  A) Depress “finger release” on ratchet and 
fold handle open.  B) Pull strap through ratchet just far enough to unhook metal ring 
from T-bar at the end of the rotating arm.  C) Perform this on both ratchets. 

 
4. 

Move the Roto-Lift forward, straddling the drum, and center the rotating arms to the 
drum using the “up/down” switch on the control box panel. 

 
5. 

After arms are centered on drum, push unit forward the rest of the way so the drum 
touches the rear of the rotating arms. 

 
6. 

Pull both straps around the front of the drum and hook the metal ring onto the T’bar on 
the end of the rotating arms. 

 
7. 

By depressing the “finger release” on the ratchet and returning it to the original position, 
you may now ratchet the straps tight around the drum. 

 
8. 

With BOTH straps tight, raise the drum by using the “up” function switch. 

 
9. 

To dump, raise the drum to the desired height and rotate the switch on the control box 
panel the direction you want the drum to dump. 

 

 

 
 
 
 
 
 
 
 

 

Summary of Contents for ROTOLIFT-78 AIR















Reviews: