7
ELECTRICAL SAFETY REgULATIONS
1) The power supply voltage must correspond to that indicated
on the technical data plate. Do not use any other type of power
supply.
2) It is advisable to install a trip switch on the electrical power
supply line. Consult your electrician.
3) Do not use the tool in damp or wet areas or in the rain.
4) The power supply cable must be checked on a regular basis
and before each use of the machine to check if it is damaged
or worn. If it is seen to be in poor conditions, do not use the
machine but have the cable repaired by an authorised service
centre.
5) If you are using an extension cable, keep it away from the
work area, from damp, wet, greasy and sharp surfaces and
also from sources of heat and combustibles.
6) If you are using a cable-reel for the extension cable, run the
whole cable out completely otherwise it could heat up and
catch fire.
7) Any extension cable used must have a section of at least 2x1.5
mm
2
.
8) Do not use the power supply cable to lift or pull the tool or to
disconnect the plug.
STARTINg AND USE
Switch:
- pos. 0=off
- pos. 1=switched on at minimum temperature
- pos. 2=switched on at maximum temperature
1) Plug in the gun.
2) Put the switch in pos. 1 (minimum temperature) and leave it
to work for about one minute.
3) Position the nozzle about 2 cm from the surface to be treated
and, if necessary, put the switch into position 2 (maximum
temperature).
4) Remove the heated paint with the help of a scraper.
5) Clean the scraper regularly to prevent accumulated paint from
catching fire.
SwITCHINg OFF
Put the switch into pos. 0 and leave the tool to cool down to room
temperature before putting it away.
MAINTENANCE
IMPORTANT! Always unplug the tool from the mains socket
and leave it to cool down completely before proceeding with
any sort of inspection or maintenance jobs.
- Take good care of your tool and clean it regularly. In this way its
efficiency will be ensured and its lifespan extended.
- Clean the tool using a soft cloth only.
- Do not wet or spray water over the tool.
- Do not use detergents or solvents to clean the tool as you could
irreparably damage it. Chemical agents can easily damage the
plastic parts.
- Remove any processing residue from the tool.
TROUBLESHOOTINg
Check that the plug is correctly plugged in to the mains socket and
that there is voltage in the system. Put the switch into positions
1 and 2.
If the problem persists following these checks, then the problem
could be in the machine itself. Have an authorised service centre
check it out.
STORAgE
Follow the tips below to store the tool:
1) Ensure that the nozzle has cooled down completely (to room
temperature).
2) Clean the machine and all its accessories thoroughly (see
MAINTENANCE section).
3) Store it: out of reach of children; in a stable and safe position; in a
warm and dry place; avoid excessively high or low temperatures.
4) Protect it from direct sunlight.
5) Do not seal it in nylon bags where humidity could form.
6) Put the machine away in its container after use.
DISPOSAL
In order to protect the environment, proceed according to the local
laws in force. Contact the relevant authorities for more information.
When the machine is not longer useable or repairable, deliver the
machine and packaging to a recycling centre. Take out the batteries
(where fitted) and dispose of them separately.
Electric and electronic waste may contain substances that
are dangerous for the environment and for human health. For this
reason they must never be disposed of together with domestic
waste, but collected separately in specific collection centres or
returned to the retailer when similar new equipment has been
purchased. The illegal disposal of such equipment may result in
prosecution to the full extent of the law.
wARRANTY
This product is guaranteed by law against non conformities with
regards to the characteristics declared, provided that is has been
used exclusively as described in this operator’s manual, has not
been tampered with in any way, has not been repaired by unau-
thorised persons, and, only if original replacement parts were
installed as needed. In any case, consumable materials and/or
components subject to wear, like batteries, light bulbs, cutting
and finishing components, etc. are excluded from this warranty.
Return the product to a retailer or an authorised customer service
centre together with proof of purchase.
AMENDMENTS
The text, figures and data correspond to the standards in place on the
date of printing the instructions contained herein. The manufacturer
reserves the right to update the documentation if changes are made
to the appliance, without being bound by any obligations.
© No part of this publication and the documentation enclosed
with the machine may be reproduced without written permission
from the manufacturer.
