background image

-  26  -

REPLACING THE LINE TRIMMER SPOOL 

OF THE SEMI-AUTOMATIC SPOOL (Fig. L)

WARNING! All operations indicated below must 

be carried out with the engine switched off and 

the spark plug cap disconnected. Always wear 

protective gloves.

WARNING! Installing the spool must be carried 

out with absolute precision. Incorrect assembly 

causes danger.

If you must replace the trimmer line, only use 

original spare parts of the same size and shape.

Before you start, carefully study the components 

and 

Fig. L

. If you are not familiar with handling 

and assembling mechanical components, we 

recommend that you contact an authorised 

service centre.

1. Wear protective gloves.

2. Disconnect the spark plug from the spark.

3. Open the spool by pressing the two side wings 

of the lower cuff (fig. L1)

4. Remove the spool and wrap the wire (not 

included) into the spool, respecting the winding 

direction indicated by the arrow (fig. L2)

Nb: Use a special wire for brush cutters, of 

round-section plastic material, with the same 

diameter of the original wire and of sufficient 

length to wrap it in the spool and without 

exceeding. It is forbidden to use metal wires.

5. Attach the two ends of the wire to the spool 

holes (fig. L3)

6. Install the spool inside the upper cap and pass 

the wires inside the bushings (fig. L4). The wire 

should protrude about 10cm.

7. Place the spring at the center of the bottom 

cuff (fig. L5)

8. Close the lower cuff by attaching it to the 

appropriate seats, if necessary by pressing 

the side tabs (fig.L6)

9. Check the correct assembly of the spool

10. Screw the spool to the conical torque 

following the instructions in the chapter ‘AS-

SEMBLING COMPONENTS’, start the machine 

and perform a vacuum test for 1 minute while 

maintaining a safe distance.

STORAGE

Clean the machine and all its accessories 

thoroughly (see Maintenance section). Protect 

unpainted parts with protective oil and use ori-

ginal packaging to protect the machine.

Store the machine in a stable and safe position 

out of children’s reach. The place must be dry, 

free from dust, temperate and protected from 

direct sunlight.

Keep children and unauthorised personnel out 

of the storage room.

WARNING! Hot surfaces. Some parts of the 

machine may stay hot for several hours after 

it has been switched off. Wait for it to cool 

down completely before storing it.

1. Remove all the fuel from the tank.

2. Remove the blade (if applicable), insert the 

guards for the cutting edges and store in a 

protective package.

3. Pour a few drops of engine oil into the spark 

plug hole, put back the spark plug and put 

the engine in the compression stroke (slowly 

operate the recoil starter lever).

DISPOSAL

In order to protect the environment, proceed 

according to the local laws in force. Contact the 

relevant authorities for more information.

When the machine is no longer useable or re-

pairable, deliver the machine and packaging to 

a recycling centre.

WARRANTY

The product is protected by law against non-

compliance with the declared characteristics 

provided it is used only in the manner described 

in the instructions, it has not been tampered with 

in any way, it has been stored properly, has been 

repaired by authorized and, where applicable, 

have been used only original spare parts.

In the case of industrial or professional use or 

when using such a guarantee is valid for 12 

months.

To issue a claim under warranty you must 

present proof of purchase to your dealer or 

authorized service center.

Summary of Contents for EASY52 FGZ





























Reviews: