background image

14

Where to mount

Valentine One works best when mounted high in the 
windshield, and toward the center between the windshield
pillars. Use your choice of windshield or visor mounts.

•  When properly mounted, the

front antenna

will look 

forward through the glass. It must have an unobstructed
view. Don’t put it behind the parked windshield wipers,
or directly behind an in-glass antenna. Don’t position it 
so that it "looks" into the rearview mirror.

• The 

rear antenna

will look rearward, between 

passengers and out the rear glass. It, too, must have an 
unobstructed view.

Detector performance is enhanced

by a high mounting 

position. Two reasons. For radar, a longer sight line to 
the horizon always helps. For laser, moving away from 
the hood and its sun reflections helps a lot.

IMPORTANT NOTE:  Windshield heaters such as Ford’s
InstaClear

®

block radar from passing through the glass (look

for a brown tint). So do 

solar barrier

windshields of the type

used on GM Venture-Montana-Silhouette-Trans Sport 
minivans and on some imported luxury sedans (look for a
reddish or copper tint). Same for mirrored sun screens.
Detector performance will be greatly reduced when V1 is
mounted behind such metallic films.

SAFETY WARNING:  Because a detector on a windshield
mount or visor mount is not permanently attached to the
car, it could come loose in a crash, possible causing injury.
Also, a passenger may move forward on impact and contact
the detector. Keep these possibilities in mind when you
mount your Valentine One.

How to mount

Mounting on visor

1.

Slide visor mount on to Valentine One.

2.

Clip to visor near center of windshield.

3.

Adjust visor angle so unit is approximately level.

4.

Connect power cord and plug into lighter socket.

 

Visor mount slides on from front.

   

Install near center of windshield.

Summary of Contents for V1









































Reviews: