manualshive.com logo in svg

Valet System One MINI, Installation Manual

Share
Download
Valet System One MINI Installation Manual Download Page 2

TABLE OF CONTENTS

GENERAL INFORMATION ............................................................ 2

LOCATION OF EQUIPMENT ......................................................... 3

ROOM STATIONS ..........................................................................

3

FRONT DOOR/GATE STATION(S) ................................................

3

POWER SUPPLY ...........................................................................

3

ANTENNA (AM/FM AERIALS) ........................................................

4

AUXILIARY INPUT JACK ...............................................................

4

AUXILIARY/LOCK OUTPUT BOARD ............................................

4

WHERE TO RUN CABLE .............................................................. 5

WHAT CABLE TO USE ? .............................................................. 5

MAXIMUM LENGTH FOR CABLE RUNS ..................................... 6

INSTALLATION OF SYSTEM ONE MINI ................................. 8-11

INSTALLATION OF DOOR/GATE STATIONS ............................ 12

INSTALLATION OF AUXILIARY INPUT JACK ........................... 12

POWER SUPPLY ........................................................................... 8

WIRING DIAGRAM ...................................................................... 10

CONTROL VOLTAGE LOAD RESISTOR ................................... 10

PROGRAMMING ROOM STATIONS .......................................... 13

KEYPAD BACKLIGHTING .......................................................... 14

DOOR STATION ADJUSTMENTS ............................................... 14

CHANGING THE CHIME ............................................................. 15

CHIME VOLTAGE OUTPUT ........................................................ 15

SIX WIRE OPERATION  USING ROOM STATIONS ................... 16

CABLE FUNCTIONS ................................................................... 17

Summary of Contents for System One MINI











Reviews:

No comments

Brands by name

Popular brands

Load more brands