1>PARTS LIST
Remove the stroller from the carton and
dispose of all packaging thoughtfully. Check
contents: 1x hood, 1x bumper bar, 1x basket,
2x front wheels, 2x rear wheels, 2x axels, 1x
brake, 1x seat.
2>TO OPEN
IMPORTANT WARNING & INSTRUCTION
YOU MUST REMOVE THE PLASTIC
PROTECTOR TO ENSURE YOUR STROLLER
LOCKS INTO POSITION.
Release frame lock on side of stroller frame (a).
Lift the stroller handle upward and over in
one contiuous motion until the lower chassis
locks into position (b). (You should hear an
audible ‘click’).
IMPORTANT WARNING: ALWAYS TEST
THAT ALL LATCHES ARE SECURELY
ENGAGED BEFORE USE.
3>REAR AXLE
Align the plastic housings of the rear brake
section with the open tubes of the rear of the
stroller chassis (c) .
IMPORTANT WARNING : BE SURE THAT
THE RED BRAKE LEVER IS UPRIGHT
Insert the housings over the open tubes until
the brake section locks securely into place.
IMPORTANT WARNING: TEST THAT THE
BRAKE SECTION IS SECURELY ENGAGED
ONTO THE STROLLER FRAME BY PULLING
ON IT FIRMLY.
4>BASKET
Align the basket frame with the open tubes at
the rear of the seat. Simultaneously pressing
in the locking buttons (d), slide the basket
frame into the housing until the buttons lock
into place.
Basket front - pass the front flap over the
bar between the seat and the seat frame (e).
Secure with the snaps. Pull the side flaps
around the front and Velcro into place on the
front flap (f).
5>REAR WHEELS
Simultaneously press on the spring loaded
axle button (g) and insert it through the
central hub of the rear wheel. Repeat this
process for the other rear wheel.
Pressing the axle button again (h), insert the
axle end into the side of the brake housing
as far as it will go. Release the axle button
and pull slightly on the wheel to ensure that
it has securely engaged.
6>FRONT WHEELS
Grasping the front wheel, align the shaft with
the hole in the underside of the swivel housing
(i). Depress the button on the top of the swivel
housing (j). Insert the shaft into the housing as
far as it can go until it engages securely.
Repeat the procedure for the other front wheel.
IMPORTANT: Pull the wheel downward to test
THAT IT HAS SECURELY ENGAGED IN THE
HOUSING.
Locking your wheels: Your front wheels can
be set to swivel freely (360º) or can be fixed
in place for use over rough or sandy surfaces.
To fix the front wheel in the non swivel position,
turn the wheel so that the two notches on both
housings line up. Press down firmly on the
swivel lock until it locks into place (k).
To unlock simply lift the locking tab until it locks
in the open position
.
7>BUMPER BAR
Insert the front bar ends into the nylon housings
located on either side of the frame. Be sure that
the bar is securely engaged.
Adjust the front bar by simultaneously pressing
the button on the bar housing and swivelling
the bar to the uppermost position (l). This is the
only position for use with a child in the stroller.
To remove the front bar: Feeling the side of
the nylon housing that sits below the frame at
each side (facing inward), locate the release
button (m). Press each release button inward
while simultaneously pulling upward on the bar
housing. Repeat for the other side. Note that
this may be difficult to do as the bar is secured
firmly as a safety precaution.
IMPORTANT WARNING: THE FRONT
BAR IS NEITHER A RESTRAINING NOR
CARRYING DEVICE.
8>FOOTREST
To adjust your foot rest downward, press the
central buttons on either side of the footrest
while simultaneously adjusting it up or down(n).
IMPORTANT WARNING: YOUR FOOTREST
IS DESIGNED TO COLLAPSE IF EXCESS
WEIGHT IS APPLIED TO IT
INSTRUCTIONS
