background image

Using the eXpanda hOOd

FIGURE M

The Expanda hood unzips, increasing the size of your standard 

hood, to give greater coverage and protection from the sun and 

weather for your child.

To open the Expanda hood:

26. Locate the zip in the center of the Expanda Hood and 

unzip completely

27. Gently pull the Expanda Hood forward until it is reaches 

its full extension.

To close the Expanda hood:

28. Gently push the Expanda Hood back, allowing the 

middle section to fold in on itself.

29. Carefully zip the Expanda Hood closed.

IMPORTANT: ALWAyS TAkE CARE WhEN CLOSING ThE  

EXPANDA hOOD TO AvOID ThE zIPPER CATChING ON ThE 

ENCLOSED FAbRIC

seat recline

FIGURE N

The new “no zip” recline offers an almost infinite amount of seat 

adjustments:

30. RECLINE: While squeezing the centre release mechanism in a 

pincer action, ease the seat down to the desired position.

30. INCLINE: Place your hand in the centre of the rear of the seat.

31. Pull the incline strap while gently pushing on the rear of the 

seat until the desired position has been reached.

IMPORTANT WARNING: ALWAyS TEST ThAT ThE SEAT IS SECURELy 

LOCkED IN PLACE.

FIGURE O

32. Before using your stroller, be sure to attach the rear seat 

tether straps to the stroller frame by feeding the strap through 

the slit in the steel buckle. While not essential for safety, these 

additionally secure the seat to the stroller frame. 

bUMper bar

FIGURE P

33. Remove the plugs from the nylon housing at either side of 

the stroller frame by pressing each inner “release button” and 

pulling the plug upward.

NOTE: DO NOT remove the plugs in the centre between both seats. 

be sure to store the removed plugs in a secure place as they MUST 

be used whenever nothing is engaged in the front bar housing to 

prevent finger entrapment.

34. Insert the bar ends into the nylon housing located on either 

side of the frame. Be sure that the red buttons are facing 

towards the seat and that the bar is securely engaged.

35. Adjust the front bar by simultaneously pressing the two  red 

buttons and swivelling the bar (forward or backward) to the 

desired position.

M

N

O

P

IMPORTANT 

WARNING:  

ThE FRONT bAR

IS NOT A 

RESTRAINING 

DEvICE.

Summary of Contents for TRIMODE









Reviews: