1>PARTS LIST
1x bumper bar (A), 1x hood (B), 2x rear
wheels (C), 2x front wheels (D), axles (E)
seat (F), stroller frame (G).
2>TO OPEN
Lay the stroller frame flat on the ground
with the handle facing upwards. Release the
frame lock if engaged (a)
Lift the handle upward to a vertical position.
You will feel the chassis unfolding as you lift.
Continue to lift the handle until you feel the
chassis lock into the open position.
IMPORTANT WARNING: ALWAYS TEST
THAT ALL LATCHES ARE SECURELY
ENGAGED BEFORE USE.
3>REAR WHEELS
Pressing on the axle release button (b),
insert the axle through the outside of the
metal hub and through the nylon brake cog.
IMPORTANT: INSERT THROUGH OUTSIDE
OF THE WHEEL - THE SIDE WHICH DOES
NOT HAVE THE BRAKE COG SPROCKETS
While pressing the axle release button (b),
insert the wheel axle into the wheel housing of
the frame at the rear of the stroller chassis (c).
Keeping the axle release button depressed,
insert the wheel as far as it will go into the
channel. Release the button and pull the
wheel slightly back toward you to ensuring
that it has locked securely into place. Repeat
this procedure for the other wheel.
To remove a rear wheel, firmly grasp the
wheel spokes while pressing the axle
release button. Gently pull the wheel free of
the wheel housing.
4>FRONT WHEELS
Line each front wheel pin (d) with the
corresponding front wheel housing (e).
Insert wheel pin into the wheel housing and
push it up until it clicks into place.
To remove the wheel, press down firmly on
the release button (f) while pulling the wheel
free of the housing.
The front wheels of your stroller offer either a
full, 360º swivel action or a locked position.
To lock the front wheel, turn the wheel so
that the bulk of it is beneath the stroller
and push down on the wheel lock (g) until
it locks into position. Repeat this procedure
for the other side.
IMPORTANT WARNING: ALWAYS TEST
THAT THE LOCKS ARE FULLY ENGAGED
BEFORE USE.
5>INSTALL SEAT
Line up the seat housing (h) with the
corresponding connectors (i) located on
either side of the stroller frame. Lower the
seat onto the connectors and gently push
the seat down until it clicks securely into
place.
NOTE: YOUR SEAT CAN BE INSTALLED
EITHER FORWARD OR REARWARD FACING.
To remove the seat, simultaneously lift one
trigger (j) on each side of the seat housings
(this can be operated from either the front
or rear of the housing) and lift the seat unit
from the frame.
6>BUMPER BAR
Insert each side of the bumper bar fitting
into the corresponding housing in the seat
frame until you hear it click into place.
The bumper bar can be opened as a “gate”
for easy access pressing on one of the
release buttons (k) and lifting the side out
of the housing. For full removal, repeat this
process for the other side.
7>HOOD
Locate the hood stud rivets found on either
side of the stroller, and align hood clamp
over each rivet. Secure clamp onto frame (l).
WARNING: HOOD MUST ALWAYS BE
FULLY INSTALLED AND ATTACHED TO
FRMAE WHEN USING SEAT IN THE FULLY
RECLINED POSITION.
The Expanda hood unzips, increasing the
size of your standard hood, to give greater
coverage and protection from the sun and
elements for your child.
To open the Expanda Hood: Locate the zip
in the center of the Expanda Hood and unzip
completely (n). Gently pull the Expanda Hood
forward until it is reaches its full extension.
To close the Expanda Hood: Gently push the
Expanda Hood back, allowing the middle
section to fold in on itself. Carefully zip the
Expanda Hood closed.
The hood offers a flow through ventilation
cap at the rear (o). To allow ventilation
simply flip the cap down.
INSTRUCTIONS
