manualshive.com logo in svg

Val-Tex Easy Lube 40-70, Operating Manual, Page: 8 / 41

Share
Download
Val-Tex Easy Lube 40-70 Operating Manual Download Page 8

 

High-Pressure Pump (Stationary and Portable)

 

SER 8540-A1

 

Alemite Corporation

3

Revision (7-98)

 

Item

No.

Part No.

Description

Qty

Notes

Numeric Order

Part #   (Item #)

 

1

8540-B

Pump Assembly, High-Pressure

1

See SER

 

 8540-B

 

6320-3

(4)

2

317875-7

Hose Assembly, Material

1

Model 8541-5

8540-B

(1)

3

44734

Adapter, 3/8 “ NPTF (m) x 1/2 " -27

1

 

17804

 

(8)

4

6320-3

Valve Assembly, Control

1

See SER

 

 6320-3

 

44734

(3)

5

B52752

Z-Swivel Assembly, High-Pressure

1

See 

 

Figure 3

 

48018

(11)

6

315943

Bushing

1

B52752

(5)

7

338371

Cover Assembly

1

 

77009

 

(12)

8

Washer, 1/4 "

3

Included w/ 338371

 

77786

 

(10)

9

Washer, Lock, 1/4 "

3

 

170561

 

(13)

10

Capscrew, 1/4 " -20 x 1/2 "

3

 

172207-1

 

(9)

11

48018

Screw, Thumb, 1/4 " -28 x 1-1/8 "

3

315953

(6)

12

Washer, Internal Tooth Lock, 1/4 "

1

316315-5

(15)

13

Screw, 1/4 " -20 x 5/16 "

1

317875-7

(2)

14

338802

Plate, Follower

1

320998-B4

(7)

15

316315-5

Dolly Assembly

1

Model 8541-5

See SER

 

 316315-5

 

338802

(14)

 

Legend

 

:

Part numbers left blank (or in 

 

italics

 

) are not available separately

 

Assembly

 

NOTE

 

: Refer to 

 

Figure 2 

 

for component

identification on all assembly procedures.

 

CAUTION

 

Select a clean environment for all assembly proce-
dures. Prevent contamination from foreign mate-

 

rial. Damage to components can occur.

 

Pump Assembly and Cover

 

IMPORTANT: Make sure to remove the pro-
tective cover from the inlet of Pump Assem-
bly (

 

1

 

). 

 

  1. Install Pump Assembly (

 

1

 

) into Cover Assembly (

 

7

 

).

  2. Secure the Pump Assembly to the Cover with 

Washers (

 

8

 

), Lock Washers (

 

9

 

), and Capscrews (

 

10

 

).

• Tighten the Capscrews securely.

 

Cover Assembly and Follower Plate

 

  3. Place Follower Plate (

 

14

 

) onto the top of the product.

• With a wobbling motion, eliminate any air that may 

be trapped underneath the Follower Plate. Force the 
product through the hole in the center of the Plate.

4. Guide the pump tube into the Follower Plate and fit the 

Cover onto the container.

5. Secure the Cover to the container with Thumb 

Screws (

 

11

 

).

 

NOTE

 

: On model 8541-5, secure the con-

tainer to Dolly (

 

15

 

). Refer to SER 

 

316315-5

 

for details.

Summary of Contents for Easy Lube 40-70










































Reviews:

No comments