Val-Tex Easy Lube 40-70 Operating Manual Download

Page: 24 / 41

$background image$

Service Guide

Alemite Corporation

PO Box 473515, Charlotte, North Carolina 28247-3515

1998 by Alemite Corporation

This document contains confidential information that is the property of Alemite Corporation

670652

and is not to be copied, used, or disclosed to others without express written permission.

Revision (2-98)

SER 331378-A1

331378-

A1, B1,
E1, F1, H1

Material

Outlet

Material Inlet

1-3/8 " (35 mm)

Dia.

Air Inlet

Description

The major components of the 331378 series pumps

consist of an air-operated motor and a pump tube. The air
motor connects directly to the double-acting reciprocating
pump tube.

These high-pressure (70:1 ratio) pumps are designed to

deliver a range of light to heavy lubricants directly from their
original drum.

Models 331378-A1, B1, E1, F1, and H1

Each pump model is designed with a pump tube length to

accommodate different size containers. See Figure 1.

The difference in the length of the pump tubes for the two

12.5 kg models is due to the design of the cover.

Model 331378-E1 bolts to a cover with a flat design

(Obsolete). Model 331378-F1 uses a cover with a bung
adapter. See the section entitled Accessories for details.

Specifications

Air Motor

Pump Tube

Piston Diameter x Stroke

Air Inlet

Max. Air Pressure

Inches

Centimeters

psi

Bars

3 x 1-5/8

76.2 x 41.3

1/4 " NPSI (f)

100

6.9

For information on the air motor, refer to Service Guide SER 324400-5

Material

Outlet

Max. Material

Pressure

Max. Delivery/Minute

(Approximate)*

Displacement

per Cycle

psi

Bars

Ounces

Grams

3/8 " NPTF (f)

7000

483

820

0.277

4.54

* For detailed information, refer to Figure 4

Table 1

Model 331378 Series Specifications

Figure 1

High-Pressure Stripped Pump

Model 331378 Series

High-Pressure Stripped Pump

Pump Model

Container Size

lbs

Inches

331378-A1

120

27-3/4

70.5

38-1/8

96.8

331378-B1

400

180

47-3/8

120.3

331378-E1

12.5

30.5

22-3/8

56.8

331378-F1

15-1/4

38.7

26-5/8

67.6

331378-H1

48.3

29-3/8

74.6

Summary of Contents for Easy Lube 40-70










































Search results

Summary of Contents for Easy Lube 40-70

Reviews:

Related manuals for Easy Lube 40-70

Brands by name

Popular brands

Val-Tex Easy Lube 40-70, Operating Manual

Search results

Summary of Contents for Easy Lube 40-70

Reviews:

Related manuals for Easy Lube 40-70

Brands by name

Popular brands