manualshive.com logo in svg

Vaisala PTU200 Series, User Manual

Share
Download
Vaisala PTU200 Series User Manual Download Page 10

U

SER

'

S 

G

UIDE

_______________________________________________________________________

6 ____________________________________________________________________ M210195

EN

-A

T

ABLE 

3-1

Pin assignment for RS 232C/TTL serial output

PIN

SIGNAL

   1

TX with diode

   2

TX/TXD/TXD inverted

   3

RX/RXD/RXD inverted

   4

external power on/off control

   5

ground for the RS 232C

   6
   7

ground for supply voltage

   8
   9

supply voltage (10...30 VDC)

T

ABLE 

3-2

Pin assignment for optional RS 232C/485/422

PIN

SIGNAL

   1

TX with diode

   2

TX/TXD/TXD inverted

   3

RX/RXD/RXD inverted

   4

external power on/off control

   5

ground for the RS 232C

   6

RS 485/422 LO

   7

ground for supply voltage and TTL level serial interface

   8

RS 485/422 HI

   9

supply voltage (10...30 VDC)

The factory settings of the PTU200 series transmitters are the
following:

T

ABLE 

3-3

Serial interface factory settings

Baud rate

9600

Parity

even

Data bits

7

Stop bits

1

Duplex

full duplex

After having made the electrical connections, switch the power on,
and the transmitter responds indicating its type and the software
version.

PTU200 / 1.01
>

The transmitter is now ready to respond to any command available.

All manuals and user guides at all-guides.com

Summary of Contents for PTU200 Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands