Vaillant VWZ MEH 60 Installation Instructions And Instructions For Use Download Page 6

Page: 6 / 16

0020152779_05 - 10/14 - Vaillant

NOTES ON THE DOCUMENTATION

Notes on the documentation

2.1

Observe other applicable documents

►

Observe absolutely all operating and installation
instructions enclosed with the product, for the various
parts and components of the system.

2.2 Storing

documents

►

Pass these instructions and all other applicable
documents to the system user.

The system user should retain these instructions so that
they are available when required.

2.3

Validity of the instructions

These instructions apply exclusively to:

Product

Type designation

Article number

VWZ MEH 60

6 kW

0020145030

Description of the product

3.1 Product

structure

3.1.1 Electrical

Module

1 Temperature

Sensor

pocket

A Heat input from the heat

pump

B Heat outlet towards the

installation

3.2

Type designation and serial number

Data plate location:

1 Data

plate

The type designation and the serial number are shown on
the data plate.

3.3

Data plate description

The data plate certi

es the country where the product is

intended to be installed.

The data plate contains the following data:

Abreviation/
symbol

Description

Country code:
"GB"

Country where the product is intended to
be installed

Serial-no

Commercial name of the product and its
serial number

min

max

Central heating maximum and minimum
hydraulic pressure

V/Hz

Electrical voltage / frequency

I max

Maximum Current

P max

Maximum absorbed power

Index of electrical protection

See chapter "CE Mark"

See chapter "Recycling and disposal "

Summary of Contents for VWZ MEH 60

















Search results

Summary of Contents for VWZ MEH 60

Reviews:

Related manuals for VWZ MEH 60

Brands by name

Popular brands

Vaillant VWZ MEH 60, Installation Instructions And Instructions For Use

Search results

Summary of Contents for VWZ MEH 60

Reviews:

Related manuals for VWZ MEH 60

Brands by name

Popular brands