Operating and display functions 5
0020237621_02 Operating instructions
11
5.1
Information
5.1.1
Reading the system status
Menu
→
Information
→
System status
–
Under
System status
, there is a list containing inform-
ation that provides an overview of the current system
status, and current settings that you can change there.
5.1.1.1 System
Menu
→
Information
→
System status
→
Fault status
–
If no maintenance is required and no faults have oc-
curred, the value
No fault
appears for
Fault status
.
If maintenance is required or a fault has occurred, the
value
Fault list
is shown for
Fault status
. In this case,
the right-hand selection button is for the
Display
function.
If you press the right-hand selection button
Display
, the
list of fault messages appears on the display.
Menu
→
Information
→
System status
→
Green IQ
–
You can use the function if the connected heat generator
Green IQ
is capable of this.
On
: The operating mode controls the heat generator in the
heating and cylinder charging mode so that a maximum
gross calorific value utilisation is achieved.
Off
: The operating mode is switched off.
Menu
→
Information
→
System status
→
Water pressure
–
You can use this function to read the water pressure of
the heating installation.
Menu
→
Information
→
System status
→
System status
–
You can use this function to read the heating installa-
tion's operating mode.
–
Standby
: The heating installation has no heat demand
and is in standby.
–
Heat. mode
: The heating installation heats the living
rooms to the
Desired heating temp.
.
–
Cooling
: The heating installation cools the living rooms
to the
Desired cooling temp.
.
–
DHW
: The heating installation heats the domestic hot wa-
ter in the cylinder to the desired temperature
Domestic
hot water
.
Menu
→
Information
→
System status
→
Collector temp.
–
You can use this function to read the current temperature
on the collector temperature sensor.
Menu
→
Information
→
System status
→
Solar yield
–
You can use this function to read the total solar yield.
Note the contents of the section Display for energy con-
sumption and energy yield (
→
Page 12).
Menu
→
Information
→
System status
→
Reset solar yield
–
If you select the
Yes
setting in the
Reset solar yield
function and press the right-hand selection button
OK
,
you reset the previously totalled solar yield to 0 kWh.
Menu
→
Information
→
System status
→
Environmental
yield
–
You can use this function to read the total environment
yield.
Note the contents of the section Display for energy con-
sumption and energy yield (
→
Page 12).
Menu
→
Information
→
System status
→
Curr. room air
hum.
–
You can use this function to read the current room air
humidity. The room air humidity sensor is installed in the
system control.
Menu
→
Information
→
System status
→
Current dew
point
–
You can use this function to read the current dew point.
The dew point indicates the temperature at which the
water vapour in the air condenses and settles on objects.
Menu
→
Information
→
System status
→
triVAI
–
You can use this function to read whether the heat pump
or the back-up boiler (gas, oil or electricity) is currently
covering the heat demand. The energy manager uses
the
triVAI
and the comfort criteria to decide which heat
generator to use.
If the value that is read is greater than 1, the heat pump is
better at covering the heat demand than the back-up boiler.
Menu
→
Information
→
System status
→
Battery status
–
You can use this function to read the battery's state of
charge.
–
OK
: The battery has sufficient charge.
–
Critical
: The battery is almost flat.
Menu
→
Information
→
System status
→
Signal strength
–
You can use this function to read how strong the radio
link between the radio receiver unit and the system con-
trol is.
–
4: The radio link is within the acceptable range. If the
reception strength is < 4, the radio link is not stable.
–
10: The radio link is highly stable.
5.1.1.2 ZONE1
Menu
→
Information
→
System status
→
Day temp. heat-
ing
–
You can use this function to set the desired day temper-
ature for the zone.
Day temp. heating
is the temperature that you want to have
in the rooms during the day or when you are at home.
Menu
→
Information
→
System status
→
Day temp. cool-
ing
–
You can use this function to set the desired day temper-
ature for the zone.
Day temp. cooling
is the temperature that you want to have
in the rooms during the day or when you are at home.
Menu
→
Information
→
System status
→
Set-back temp.
heat.
–
You can use this function to set the desired set-back
temperature for the zone.
Set-back temp. heat.
is the temperature that you want to
have in the rooms during the night or when you are away
from home (night mode).
Menu
→
Information
→
System status
→
Room temperat-
ure
–
If the system control is installed outside of the heat gen-
erator, you can read the current room temperature.
