12
Operating instructions 0020262548_01
Individual dates vary from
the selected time programme
Mo-Su.
OK
Back
If you press the right-hand selection button
Select
, a mes-
sage appears on the display which informs you about differ-
ent time periods. You do not need to adjust the times.
You can use the right-hand selection button
OK
to display
and change the set times for the block marked with !!.
5.2.3.4 Setting the Heating time programme
Menu
→
Time programmes
→
ZONE1
–
The time programmes are only effective for the
Heat-
ing
operating mode in automatic mode. Within the time
periods, the system control brings the temperature of
the connected rooms to the set desired temperature
Day
temp. heating
. Outside of these time periods, the sys-
tem control switches to the operating mode that the com-
petent person has set:
Eco
or
Set-back temp. heat.
. If
the competent person has left the factory setting
Eco
, the
system control switches off the heating function.
Setting the
Heating
operating mode. (
5.2.3.5 Setting the Cooling time programme
Menu
→
Time programmes
→
ZONE1
:
Cooling
–
The time programmes are only effective in the
Cooling
mode and the
Manual cooling
advanced function. In
each set time period, the desired temperature that you
set in the
Desired temperatures
function applies. Within
the time periods, the zone cools the living areas to the
desired
Day temp. cooling
temperature. Outside this
time period, there is no cooling.
5.2.3.6 Setting the domestic hot water generation
time programme
Menu
→
Time programmes
→
DHW circuit
–
The time programmes are only effective for domestic hot
water generation in automatic mode. In each set time
period, the desired
Domestic hot water
temperature
applies. At the end of a time period, the system control
switches the domestic hot water generation off until the
start of the next time period.
5.2.3.7 Setting the time programme Circulation
Menu
→
Time programmes
→
Circulation
–
The time programmes are only effective for circulation
in Automatic mode. The set time periods determine the
operating times for circulation. Within the time period, the
circulation is switched on. Outside the time period, the
circulation is switched off.
5.2.3.8 Setting the Ventilation time programme
Menu
→
Time programmes
→
Ventilation
–
The time programmes are only effective for ventilation
in automatic mode. In each set time period, the ventila-
tion level that you set in the
Ventilation
function applies.
Within the time period, the system control regulates the
ventilation unit to
Max. vent. stage: Day
as a maximum.
Outside the time period, the system control regulates the
ventilation unit to
Max. vent. stge: Night
as a maximum.
5.2.3.9 Setting the High tariff time programme
Menu
→
Time programmes
→
High tariff
–
You can use this function to set when the high tariff or the
low tariff should be used to calculate the costs.
Within the time period: For the high tariff
Outside of the time period: For the low tariff
The times of high tariff depend on your energy supply com-
pany.
If the energy supply company only offers one tariff, you do
not need to set any time periods. The cost for the electricity
is calculated using one tariff.
Setting costs (
5.2.4
Days away from home scheduling
Menu
→
Days away from home scheduling
–
You can use this function to set a period of time and a
temperature for the days that you are away from home.
Heating installation operation during the set time
period
–
The domestic hot water is not being heated.
–
The previously set temperature applies for all zones.
–
The ventilation runs at the lowest ventilation level.
–
The cooling is switched off.
While the
Days away from home scheduling
function is
activated, it has priority over the set operating mode. At the
end of the specified period, or if you cancel the function, the
heating installation returns to the pre-set mode.
5.2.5
Day at home scheduling
Menu
→
Days at home scheduling
–
In the specified period, the heating installation works in
the
Automatic mode
mode and uses the day settings for
Sunday
, which were set using the
Time programmes
function. At the end of the specified period, or if you can-
cel the function, the heating installation returns to the pre-
set mode.
5.2.6
Select language
Menu
→
Basic settings
→
Language
–
You can use this function to change to the language that
you want to appear in the display.
