background image

Operating manual Remote control device VR 90 0020055329_00

10

Displayed menu

Explanation and setting options

The following information is displayed on the basic display: 
the current date and time, the outside temperature  (if room modulation is activated), 
the current room temperature, the current operating mode and the target room 
temperature. 
Each heating circuit or hot water circuit is controlled separately according to the 
operating mode. 

The heating, energy saving, auto, eco and off operating modes are available:
Auto 

The selected circuit is operated automatically between the desired set 
point and set back temperatures according to the on and off time 
programmes.

Eco

The selected circuit is operated automatically between the desired set 
point and fully off according to the on and off timer programmes. The 
frost protection function will still activate if enabled.

Heating

The selected circuit operates continuously ‘on’ at the desired ‘on’ 
temperature set point, regardless of the programmed times.

Energy sav

The selected circuit operates continuously ‘on’ at the desired ‘off/setback’ 
temperature set point, regardless of the programme times.

Off

The selected circuit is continually off except for when frost protection is 
activated..

Table 2.1 Adjustable parameters

2 Operation

Fr   17.05.02

heat zone 1

15:37

> heating

   

- 15°C

22°C

>select operation mode

room temperature 

              

21° C

Summary of Contents for VR 90

































Reviews: