background image

61

Manual - Solar hot water systems 0020009607_02

Maintenance 

Maintenance interval 

Solar circuit

 

Check the frost protection of the solar fluid (use the Vaillant 302 064 solar fluid tester)

Annually 

Check the system pressure 

Annually 

Check the pH value of the solar fluid (with litmus paper, pH > 7.5)

Annually 

Check the solar pump function

Annually 

Bleed the system 

Annually 

Check the circulating volume in the solar circuit

Annually 

Check the hot water thermostat mixer function

Annually 

Refill with solar fluid if necessary 

Annually 

Check the quantity of blow-off liquid 

Annually 

Release the return flow preventer

Annually 

Check the charge pressure of the expansion vessel Annually 

Collector

 

Visual inspection of the collector, collector fastenings and connections 

Annually 

Check whether the brackets and collector components are clean and fitted properly 

Annually 

Check the pipe insulation for damage 

Annually 

Solar control

 

Check the pump function (on/off, automatic)

Annually 

Check the sensor temperature display

Annually 

Secondary return/reheating

 

Check the circulation pump

Annually 

Check the timer/time programme settings

Annually 

Reheating: does it deliver the desired deactivation temperature? 

Annually 

Solar  cylinder

 

Bleed the heat exchanger if necessary

Annually 

Check the connections for leaks 

Annually 

Check the temperature and pressure relief valve

Annually

Checking the expansion relief valve

Annually

Table 7.1 Maintenance checklist

Checking the temperature and pressure relief valve 
and expansion relief valve

•  Actuate each valve manually by turning the valve cap 

and check whether the water flows unhindered to the 
discharge point via the tundish. Make sure both valves 
fit properly in idle position. 

Checking the charge pressure of the expansion vessel

•  Block the water supply and open the nearest hot water 

tap to reduce the pressure from the secondary water 
system.

•  Check the pressure of the expansion vessel at the 

measurement point with a pressure gauge. If the 
pressure is below 3.0 bar, increase it with an 
appropriate air pressure pump.

•  Perform the maintenance part of the start-up protocol.

h

 Note!

Only use original spare parts from Vaillant Ltd. 
for the replacement of parts.

Inspection and maintenance 7

                                                   

Summary of Contents for Solar System and auroSTOR unvented solar...






































































Reviews: