background image

29

Manual - Solar hot water systems 0020009607_02

Immersion heater

The auroSTOR solar cylinders are equipped with an 
additional immersion heater of 3 kW, including the 
operating thermostat and energy cut-off device.The 
immersion heater is situated behind the front plate. It is 
designed for use in unvented cylinders and includes a 
thermostat control and thermal cut out for over heat 
protection.

Note:
In the event of a replacement, only the right 
immersion heater equipped with a thermal cut 
out for overheating protection may be used.

Secondary return

The water control pack has a connection for a secondary 
return.
•  Remove the 3/4“ dummy plug (BSP thread) from the 

water control pack.

•  Connect a WRAS-approved circulating pump, which 

contains a non-return valve, to the water control pack 
(see Fig. 5.1).

•  Establish the connection to the secondary return.

5.1.2 

Technical data of the auroSTOR solar cylinder

Entry

Unit 

VIH S GB 200 S 

VIH S GB 250 S 

VIH S GB 300 S 

Cylinder:

Size

l 200 

250 

300 

Maximum water supply pressure

bar 

10 

Operating pressure 

bar 

3.5 

Pressure limiting valve

bar 

3.5 

Expansion relief valve

bar 

6.0 

Hot water expansion vessel admission pressure

bar 4.0 

Temperature and pressure relief valve

°C/bar 

95 / 7.0 

Net weight

kg 

39 

44 

49 

Weight (full)

kg 

245 

310 

340 

Height mm 

1499 

1789 

2109 

Cylinder connections:

Cold water supply

22 mm pressure pipe

Hot water connection 

22 mm pressure pipe 

Pressure-controlled cold water outlet

22 mm pressure pipe  

Secondary return

Inches

G 3/4

Flow (boiler/solar circuit)

22 mm pressure pipe

Return (boiler/solar circuit)

22 mm pressure pipe

Electrical connections:

3 kW immersion heater (according to ENBS 60335)

230/240 V, 50 Hz 

Length of the immersion heater

mm 

430 

Motorised 2 port valve

230/240 V, 50 Hz 

Cylinder thermostat

230/240 V, 50 Hz 

Thermal cut out for solar pump

230/240 V, 50 Hz 

Heating coil:

Heat loss

kW/24 h 

1.9

2.1

2.4

Heat up time (boiler part)

mins 

21

26

30

Recovery (boiler part)

mins 

13

16

21

Table 5.4 Technical data of the auroSTOR solar cylinder

Note!
The heat-up time is based on a primary flow 
rate of 9 l/min at 80 °C.
Temperature rise from 15 °C to 65 °C

Installation 5

NOTE 
The water control group used is the same as on our uniSTOR  
cylinders and has a connection that can be used for secondary  
circulation on those cylinders, it may also be used for the  
connection of a legionella circulation pump connection. 
In solar systems secondary circulation is not recommended as it  
will waste energy and reduce solar gains. as it heats the cold store  
area but of course can be used for the connection of a legionella 
circulation pump. 
 
 

                                                                                                                                                             .

Summary of Contents for Solar System and auroSTOR unvented solar...






































































Reviews: