background image

Notes on the documentation 2

0020149575_01 ecoCRAFT exclusive Operating instructions

7

2 Notes on the

documentation

2.1 Observing other applicable

documents

You must observe all operating instruc-
tions enclosed with the system compon-
ents.

2.2 Storing documents

Keep this manual and all other applic-
able documents safe for future use.

2.3 Validity of the instructions

These instructions apply only to:

Product

Article numbers

VKK GB 806/3-E
R1

0010014388

VKK GB 1206/3-
E R1

0010014389

VKK GB 1606/3-
E R1

0010014390

VKK GB 2006/3-
E R1

0010014391

VKK GB 2406/3-
E R1

0010014392

VKK GB 2806/3-
E R1

0010014393

3 Product description

3.1 Identification plate

The identification plate is mounted on the
rear of the product. The identification plate
contains the following information:

Serial number

Type designation

Designation of the type approval

Technical data

CE label

The seventh to sixteenth digits of the serial
number on the identification plate form the
article number.

3.2 Opening the front flap

1

2

Open the front flap by lifting the silver
handle bar

(1)

.

The front flap

(2)

automatically swiv-

els downwards and the control panel
becomes accessible.

3.3 Overview of the operator

control elements

1

Display

2

i

button

3

Control (access-
ory)

4

Main switch

5

+

button

6

button

7

Fault clearance

key

8

Heating flow
temperature
rotary knob

9

Rotary knob for
the cylinder tem-
perature in the
domestic hot wa-
ter cylinder

The display shows the current heating flow
temperature, the system pressure of the

Summary of Contents for ecoCRAFT exclusive

























Reviews: