Vaillant ecoCOMPACT VCC4 Series Installation And Maintenance Instructions Manual Download Page 42

Page: 42 / 68

11 Decommissioning

Installation and maintenance instructions ecoCOMPACT 0020181421_04

10.11 Completing repair work

▶

Check that the product functions correctly and check the
leak-tightness (

→

Page 26).

11 Decommissioning

11.1

Decommissioning the product

▶

Switch off the product.

▶

Disconnect the product from the power mains.

▶

Close the gas isolator cock.

▶

Close the cold water stop cock.

▶

Close the heating stop cock.

▶

Drain the unit's heating circuit. (

→

Page 34)

12 Recycling and disposal

Disposing of the packaging

▶

Dispose of the packaging correctly.

▶

Observe all relevant regulations.

13 Customer service

13.1

Customer service

Applicability:

Austria

Vaillant Group Austria GmbH

Clemens-Holzmeister-Straße 6

1100 Wien

Telefon 05

7050

Telefax 05

7050

1199

Telefon 05

7050

2100 (zum Regionaltarif österreichweit, bei

Anrufen aus dem Mobilfunknetz ggf. abweichende Tarife -
nähere Information erhalten Sie bei Ihrem Mobilnetzbetrei-
ber)

[email protected]

www.vaillant.at

www.vaillant.at/werkskundendienst/

E-Mail Kundendienst: [email protected]

Internet Kundendienst: http://www.vaillant.at/werkskunden-
dienst/

Telefon: 05

7050

2100 (zum Regionaltarif österreichweit, bei

Anrufen aus dem Mobilfunknetz ggf. abweichende Tarife -
nähere Information erhalten Sie bei Ihrem Mobilnetzbetrei-
ber)

Der flächendeckende Kundendienst für ganz Österreich ist
täglich von 0 bis 24 Uhr erreichbar. Vaillant Kundendienst-
techniker sind 365 Tage für Sie unterwegs, sonn- und feier-
tags, österreichweit.

Applicability:

Belgium

N.V. Vaillant S.A.

Golden Hopestraat 15

B-1620 Drogenbos

Tel. 2

3349300

Fax 2

3349319

Kundendienst / Service après-vente / Klanten-
dienst 2

3349352

[email protected]

www.vaillant.be

Kundendienst / Service après-vente / Klantendienst:
2

3349352

Applicability:

Germany

Auftragsannahme Vaillant Kundendienst: 02191

5767901

Summary of Contents for ecoCOMPACT VCC4 Series





































































Search results

Summary of Contents for ecoCOMPACT VCC4 Series

Reviews:

Related manuals for ecoCOMPACT VCC4 Series

Brands by name

Popular brands

Vaillant ecoCOMPACT VCC4 Series, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for ecoCOMPACT VCC4 Series

Reviews:

Related manuals for ecoCOMPACT VCC4 Series

Brands by name

Popular brands