background image

2

  

3

Please read these instructions carefully before starting installation and keep for  

future reference.
Remove all packaging and check the product for missing parts or damage before 

starting installation.
Any alterations made to this product and fittings may infringe water regulations and 

will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority 

Regulations/Byelaws and Building and Plumbing Regulations.  

To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.

General installation

Operating Specifications

Important - please read

Operating Pressure

Minimum operating pressure 

1 bar 

Maximum operating pressure 

5 bar

This fitting is a mixing device and therefore water supplies should be reasonably 

balanced.
When installed, the fitting must comply with the requirements of the Water Supply 

(Water Fittings) Regulations 1999 and Scottish Byelaws 2004. 

For further information, contact the Water Regulations department of your local water 

supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations 
Advisory Scheme by email (info

@

wras.co.uk) or telephone: 01495848454.

Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed 

to remove debris. Failure to do so could result in damage or low flow from the mixer 

unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 13.
The fitting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing 

and maintenance. No costs relating to inadequate access can be accepted.

Contents of Packaging

Installation guide &  

User manual

Mixer with o-ring

Fixing Kit

Flexible hoses

Metal washer

Rubber washer

 

Threaded rod 

Nut

MONO BIDET MIXER WITH 

POP-UP WASTE

INSTALLATION / 

USER MANUAL

KEEP FOR FUTURE REFERENCE

NURI

Waste

Waste control 

rod

Summary of Contents for AXCES NURI AX-NUR-110-CP







Reviews: