VADA V-150VF Installation Manual Download Page 10

19

18

VADA 

SUMP PUMP WITH VERTICAL FLOAT

 

V-150VF 

INSTALLATION MANUAL

WARRANTY

You have purchased a quality product  
from Reece. This product is covered by a  
2 year product warranty. This warranty covers 
faults in the product construction, material,  
and assembly. 

If a product is suspected of being faulty, please 
contact the Reece store it was purchased 
from and the product will be inspected 
by an authorised Reece representative. 
Products which are found upon inspection 
to be defective in construction, material, or 
assembly, will be replaced with an equivalent 
product free of charge within the warranty 
period outlined above. Replaced items become 
Reece’s property.

All replacement products will be available  
for collection without charge to the customer 
at the nearest Reece branch to the customer’s 
location, or elsewhere as agreed between the 
customer and Reece.

Any attempt to repair the device by the 
customer or unauthorised third parties shall 
terminate the warranty.

WARRANTY CONDITIONS

The warranty will apply only under all the 
following conditions:

•  The pump has been installed by a qualified, 

licenced personnel. 

•  The installation manual has been adhered to. 

•  The pump is in good condition and has not 

arrived damaged. 

•  The pump is located so that it will NOT be 

prone to freezing.

•  The pump is being used with clean and 

grey water and is NOT being used with 
alternative fluids specifically abrasive, 
corrosive, or explosive fluids.

•  The pump is isolated from electrical supply 

during installation and any subsequent 
service work.

•  The electrical installation is in accordance 

with the national wiring rules (AS/NZS 3000) 
for class 1, IP68 rated products. 

•  The pump has NOT been lifted/moved/carried 

by the electrical or float switch cables.

•  The pump has NOT run dry or with the 

motor exposed (i.e., out of the water for long 
periods). Running the pump dry will harm 
the pumps seal and overheat the motor. 

•  The Vada V-150VF is correctly sized for your 

application. 

•  The pump has been installed for and 

subjected to domestic residential use only 
subject to local building a municipality 
guideline. 

•  Failure is due to a fault in the manufacture  

of the project. In this case, proof of purchase 
including the date of purchase is required.

This warranty does not include faults caused by:

•  Failure to adhere to the conditions above 

•  Normal wear and tear

•  Inadequate or complete lack of maintenance

•  Chemical, electrochemical, or electrical 

influences

•  Harsh detergents or abrasive cleaners used 

on product finishes.

EXCLUSIONS

To the fullest extent permitted by law, Reece 
excludes all liability for damage or injury to 
any person, damage to any property and any 
indirect consequential or other loss or damage. 
To the maximum extent permitted by law, 
Reece excludes all warranties other than those 
set out above.

Summary of Contents for V-150VF












Reviews: